manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Поделиться
Скачать
Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 13

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

 

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM   

13 

 
AUXILIARY INPUTS

, auxiliary inputs can be user configured and will display the message as written by the user. 

 

Example 

Alarm

 

Warning 

Bearing temp high 

 

LOW FUEL LEVEL. 

will be displayed if the fuel level detected by the fuel level sender falls below the low fuel level 

setting. 

 

Alarm

 

Warning 

Low fuel level 

 

CAN ECU ERROR 

If the module is configured for 

CAN instruments

 and receives an “error” message from 

the engine control unit, ‘Can ECU error” is shown on the module’s display and a warning alarm is generated. 

 

Example 

Alarm 

The display will alternate 
between the text display and the 
manufacturers error codes

 

Alarm

 

Can ECU error 

Exhaust high 

temperature 

Can ECU error 

SPNnnnnnnn 

FMInnnnnnn 

 

4.2 ANALOGUE 

PRE-ALARMS 

 

The following alarms are termed ‘pre-alarms’ as they pre warn the operator of a potentially more serious alarm 
condition. For instance, if the engine temperature rises past the pre alarm level, a warning condition will occur to 
notify the operator. If the temperature falls below this level, then the alarm ceases, and the set will continue to run 
as normal. However if the temperature continues to rise until the coolant temperature trip point is reached, the 
warning is escalated and a high coolant temperature shutdown is initiated. 

 

LOW OIL PRESSURE

, if the module detects that the engine oil pressure has fallen below the low oil pressure pre-

alarm setting level after the 

Safety On

 timer has expired, a warning will occur.  Alarm Warning Low Oil Pressure 

will be displayed. 

 

Alarm

 

Warning 

Low oil pressure 

 

HIGH ENGINE TEMPERATURE

 if the module detects that the engine coolant temperature has exceeded the high 

engine temperature pre-alarm setting level after the 

Safety On

 timer has expired, a warning will occur.  Alarm 

Warning High Coolant Temperature will be displayed. 

 

Alarm

 

Warning 

High temperature 

 

LOW ENGINE TEMPERATURE

 if the module detects that the engine coolant temperature has fallen below the low 

engine temperature pre-alarm setting level after the 

Safety On

 timer has expired, a warning will occur.  Alarm 

Warning Low Coolant Temp will be displayed. 

 

Alarm

 

Warning 

Low Coolant Temp 

 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Содержание DSE5320



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды