manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Поделиться
Скачать
Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 30

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

30   

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM 

If the module PIN number has been set, the PIN number request is then shown. The configuration cannot be 
viewed or changed until the PIN number is correctly entered.  

 

Enter either the ‘main’ PIN or the application PIN. 

 

If no PIN has been set, then skip to the next section. 

 

NOTE:- The ‘Application Editor’ must be enabled first in order to make it accessible from the 

module’s fascia. This is done by setting a PIN (number) for the module’s main front panel editor, using the 

5xxx for Windows™ PC configuration software. 

 

 

Enter pin

 

The first * is flashing. Press + or – buttons to adjust  it to the correct value for the first digit of the 
PIN number.  
Press 

9

 when the first digit is correctly entered. 

The entered digit will turn back to a * to maintain security. 

**** 
 

 

Enter pin

 

The second * is now flashing. Press + or – buttons to adjust it to the correct value for the second 
digit of the PIN number.  
Press 

9

 when the second digit is correctly entered. 

The entered digit will turn back to a * to maintain security. 

**** 

 

Enter pin

 

The third * is now flashing. Press + or – buttons to adjust it to the correct value for the third digit 
of the PIN number.  
Press 

9

 when the third digit is correctly entered. 

The entered digit will turn back to a * to maintain security. 

**** 
 

 

Enter pin

 

The fourth * is now flashing. Press + or – buttons to adjust it to the correct value for the fourth 
digit of the PIN number.  
Press 

9

 when the fourth digit is correctly entered. 

**** 
 

 

 

NOTE:-  When 

9

 is pressed after editing the final PIN digit, the PIN is checked for validity. If the 

number is not correct, the editor is automatically exited. To retry you must re-enter the editor as 

described above. 

 

Oil pressure pre-alarm

 

If the Configuration PIN has been entered successfully (or the PIN number has 
not been set in the module) the first configurable parameter is displayed : 

 

2 

Bar

 30 

PSI

  

200 

kPa 

 

 

NOTE:- To exit the front panel configuration editor at any time, press the Stop/Reset  

 button. 

Ensure you have saved any changes you have made by pressing the 

9

 button first. 

 

NOTE:-  When the editor is visible, it is automatically exited after 5 minutes of inactivity to ensure 

security. 

 

NOTE:- If the Application Menu PIN is entered, then only the Application Menu is displayed. If the 

Full Configuration PIN is entered, the entire configuration menu is displayed including the Application 

Menu. 

 

NOTE:-  The PIN number is automatically reset when the editor is exited (manually or automatically) 

to ensure security. 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Содержание DSE5320



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды