Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 4

Страница: 4 / 66

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual

Part No. 057-014 5320 OPERATING MANUAL ISSUE 5.1 18/06/2007 ADM

8.2.1

PLUG “A” 8 WAY ........................................................................................................ 43

8.2.2

PLUG “B” 11 WAY ...................................................................................................... 43

8.2.3

PLUG “C” 3 WAY ........................................................................................................ 44

8.2.4

PLUG “D” 4 WAY ........................................................................................................ 44

8.2.5

PLUG “E” 8 WAY ........................................................................................................ 44

8.2.6

PLUG “F” 4 WAY ......................................................................................................... 45

8.2.7

PLUG “G” 5 WAY ........................................................................................................ 45

8.2.8

PLUG “H” 4 WAY ........................................................................................................ 45

8.2.9

PURCHASING ADDITIONAL CONNECTOR PLUGS FROM DSE ............................ 45

SPECIFICATION .............................................................................................46

COMMISSIONING .......................................................................................47

10.1.1

PRE-COMMISSIONING .............................................................................................. 47

FAULT FINDING ..........................................................................................49

FACTORY DEFAULT CONFIGURATION ...................................................50

TYPICAL WIRING DIAGRAM ......................................................................54

APPENDIX ...................................................................................................55

14.1

ALTERNATIVE WIRING TOPOLOGIES ....................................................................... 55

14.1.1

3 PHASE, 3 WIRE ....................................................................................................... 55

14.1.2

1 PHASE, 2 WIRE ....................................................................................................... 56

14.1.3

2 PHASE, 3 WIRE ( 2 PHASE CENTRE TAP NEUTRAL) ......................................... 56

14.2

ICONS AND LCD IDENTIFICATION ............................................................................. 57

14.2.1

PUSH BUTTONS ........................................................................................................ 57

14.2.2

STATUS / MEASUREMENT UNITS ........................................................................... 57

14.2.3

LED INDICATION ....................................................................................................... 57

14.3

5320 IDMT TRIPPING CURVES (TYPICAL) ................................................................. 58

14.4

SENDER WIRING RECOMMENDATIONS .................................................................... 59

14.4.1

EARTH RETURN SENDERS ..................................................................................... 59

14.4.2

INSULATED RETURN SENDERS ............................................................................. 59

14.4.3

FUEL LEVEL SENDERS ............................................................................................ 59

14.5

CAN INTERFACE .......................................................................................................... 61

14.6

OUTPUT EXPANSION ................................................................................................... 61

14.6.1

RELAY OUTPUT EXPANSION (157) ......................................................................... 61

14.6.2

LED OUTPUT EXPANSION (548) .............................................................................. 61

14.7

INPUT EXPANSION ....................................................................................................... 61

14.8

COMMUNICATIONS OPTION CONNECTIONS ........................................................... 62

14.8.1

DESCRIPTION ............................................................................................................ 62

14.8.2

PC TO CONTROLLER (DIRECT) CONNECTION ..................................................... 62

14.8.3

MODEM TO CONTROLLER CONNECTION ............................................................. 62

14.8.4

RS485 LINK TO CONTROLLER ................................................................................ 63

14.8.5

MODBUS™ ................................................................................................................. 64

14.9

ENCLOSURE CLASSIFICATIONS ............................................................................... 65

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание DSE5320



































































Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды