DeDietrich MODULENS O AFC 18, Инструкция по установке и обслуживанию, Страница: 118 / 180

Installer level - #SECONDARY INSTAL.P menu
Parameter Adjustment range Description Factory
setting Customer
setting
ANTICIP.C
(1) 0.0 to 10.0 Activation and adjustment of the
anticipation time
¼ "
ANTICIP.A
,
ANTICIP.B
,
ANTICIP.C
", page 119
NO
ROOM INFL.C
(2)
0 to 10 Influence of room sensor C
¼ "
ROOM S.INFL
", page 120
3
SCREED DRYING NO, B, C, B+C
Drying the floor
¼ "
SCREED DRYING
", page 119
NO
START DRYING TEMP
(3) 20 to 50 °C Screed drying start temperature 20 °C
STOP DRYING TEMP
(3) 20 to 50 °C Screed drying stop temperature 20 °C
NB DAYS DRYING
(3)
0 to 99 0
NIGHT
(2)
DEC.
The lower temperature is maintained
(Night mode)
¼ "
NIGHT
", page 120
DEC.
STOP
The boiler is stopped (Night mode)
¼ "
NIGHT
", page 120
IN 0-10V
OFF
/
TEMPERATURE
/
POWER %
Activating the 0-10 V function
¼ "Function 0-10 V", page 121
OFF
VMIN/OFF 0-10V
(2)(4) 0 to 10 V Voltage corresponding to the instruction
set minimum
0.5 V
VMAX 0-10V
(2)(4)
0 to 10 V Voltage corresponding to the instruction
set maximum
10 V
CONS.MIN 0-10V
(2)(4)
0 to 100 °C / 0 to 100 % Minimum temperature or relative power
setpoint
5 °C / 0%
CONS.MAX 0-10V
(2)(4)
5 to 100 °C / 5 to 100 % Maximum temperature set point or
relative output
100 °C / 80%
BAND WIDTH
(2)
4 to 16 K Control unit bandwidth for the 3-way
valves.
Option of increasing the bandwidth if the
valves are rapid or of reducing it if they
are slow.
12 K
BOIL/3WV SHIFT
(2) 0 to 16 K Minimum temperature difference
between the boiler and the valves
4 K
H.PUMP DELAY
(2) 0 to 15 minutes Timing of the shutdown of the heating
pumps.
The timing of heating pump shutdown
prevents the boiler overheating.
4 minutes
DHW.PUMP DELAY
(2) 2 to 15 minutes Timing of the shutdown of the domestic
hot water pump.
The timing of the domestic hot water load
pump shutdown prevents the boiler and
the heating circuits overheating (Only if a
load pump is used).
2 minutes
ADAPT ON
Automatic adaptation of the heating
curves for each circuit with a room sensor
with an influence of >0.
OFF
OFF
The heating curves can only be modified
manually.
(1) The parameter is only displayed if
INSTALLATION
parameter is set to
EXTENDED
(2) The parameter can be set to the heating curve by pressing key f
(3) The parameter is only displayed if
SCREED DRYING
is other than
OFF
(4) The parameter is only displayed if
IN 0-10V
is set to
ON
.
(5) The parameter is only displayed if
LEG PROTEC
is different from
OFF
(6) The parameter is only displayed if
P.DHW
is set to
PUMP
6. Commissioning AFC 18 - AFC 24 - AFC 30
116 09/07/2015 - 300026439-07