DAVIS TMS-5500-SL страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 48

background image

Installation

WARNING-HIGH VOLTAGE!!

Improper handling or use of this

product could result in severe electrical
shock. Have a qualified technician only

install this traction control system!!

Failure to properly insulate connection

could result in electrical shock!

Installation of the system is very simple. It is very
important to make all connections correctly.

Improper installation could result in poor system
performance or damage to the unit.

The unit should be mounted away from any sources
of electrical noise or high heat. It can be easily
mounted with Velcro to allow for easy removal.

Also, follow all recommendations made by the
ignition system manufacturer pertaining to the
routing of wires, type of spark plugs, and wires used.

For best performance, suppression type plug wire
are recommended. Solid core wires typically found
on magneto systems may cause improper operation
of the unit, and possibly permanently damage the
unit.
MSD

®

Super Conductor® wires are recommended.

Resistor type racing plugs may also be used if
supression wires are not available.

6

Davis Technologies TMS-5500-SL Elec Points

www.moretraction.com

«
...
6
7
8
9
10
...
»

Содержание TMS-5500-SL

















































Отзывы:

Нет отзывов

Похожие инструкции для TMS-5500-SL

Бренд: GE Страницы: 8

Бренд: Eaton Страницы: 86

Бренд: Jafar Страницы: 10

Бренд: Walimex Pro Страницы: 68

Бренд: Rachio Страницы: 2

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 20

GEMINI C Series

Бренд: NAPCO Страницы: 24

Бренд: Parkside Страницы: 86

Бренд: Yamaha Страницы: 92

Бренд: York Страницы: 24

Бренд: YASKAWA Страницы: 340

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды