DAVIS TMS-5500-SL страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 48

background image

Confirming Settings

The current setting for the different adjustments can
be verified at any time using the Test button and the
LED. This process is divided into 2 sections.

Standard, Advanced and Mag. The different sections
are chosen by the position by the dial when the
verification is started.

Standard

values can be verified at any time by

following these steps.

1.

Turn the power “On”

2.

Set “M” dial any position from 1-7.

3.

Press the “Test” button and HOLD

DOWN.

4.

The LED will glow solid for 8

seconds (as in the Forced Activation Test),

then blink to show the firmware version.

5.

Next the LED will flash the value for the Buffer.

(A setting of zero is indicated by a short blip of
the LED).

6.

After a short pause, the Led will flash for the
value of Sample Rate, followed by a pause.

8.

Lastly, the LED will Flash the current Self
Learning status value.

(for tech support

purposes only).

23

Davis Technologies TMS-5500-SL Elec Points

www.moretraction.com

«
...
23
24
25
26
27
...
»

Содержание TMS-5500-SL

















































Отзывы:

Нет отзывов

Похожие инструкции для TMS-5500-SL

Бренд: Watts Страницы: 2

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Daktronics Страницы: 5

Бренд: Daikin Страницы: 12

Бренд: eclisse Страницы: 40

Бренд: HANYOUNG NUX Страницы: 56

Бренд: National Instruments Страницы: 2

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: Radionics Страницы: 14

Бренд: NAiS Страницы: 144

Бренд: Panasonic Страницы: 8

Бренд: Jetter Страницы: 24

Бренд: POLA Страницы: 2

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

Бренд: Watts Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды