manualshive.com logo in svg

Dataq DI-725/E, Руководство пользователя

Поделиться
Скачать
Dataq DI-725/E Скачать руководство пользователя страница 7

DI–720/DI–722/DI–730 Series User Manual

Table of Contents

vii

Table of Contents

Warranty and Service Policy  ................................................................................................................  iii
  CAUTION   ...........................................................................................................................................  v
1. Introduction  ........................................................................................................................................  1

Features ..............................................................................................................................................  1
Analog Input  ......................................................................................................................................  1
Analog Output  ...................................................................................................................................  2
Digital Input and Output (DI-720 Series Only) .................................................................................  2

2. Specifications  ......................................................................................................................................  3
3. Getting Started  ...................................................................................................................................  7

Unpacking ..........................................................................................................................................  7
Applying Power to the DI-7xx Series Instrument  .............................................................................  7
Printer Port Instrument Installation  ...................................................................................................  8
USB Instrument Installation  ..............................................................................................................  10
Ethernet Instrument Installation  ........................................................................................................  12

Installing an Ethernet Device Directly Connected to your PC or Connected via a Hub/Switch where 
ONLY DI-72x, DI-730, or DI-78x Products are Installed  ..........................................................  13
Installing an Ethernet device via a distributed network without a DHCP server where one or more 
DATAQ Instruments devices will coexist with other Ethernet devices, and where static IP address 
are individually assigned .............................................................................................................  15
Installing an Ethernet device via a distributed network with a DHCP server .............................  17
Connecting your Ethernet Instrument to your PC or Network  ...................................................  17
Installing WinDaq software for Ethernet Products  .....................................................................  18
Daisy-Chaining Multiple Ethernet Products  ...............................................................................  19
TCP/IP Manager (Ethernet Models Only)  ..................................................................................  20
WinDaq Waveform Navigator (Ethernet models only)  ..............................................................  21

4. Instrument Controls, Indicators, and Connectors ..........................................................................  23

DI-720 Series Instrument Front Panel  ...............................................................................................  23
DI-722 Series Instrument Front Panel  ...............................................................................................  25
DI-730 Series Instrument Front Panel  ...............................................................................................  27
DI-720, DI-722, and DI-730 Series Instrument Rear Panel  ..............................................................  28

5. Calibration Verification .....................................................................................................................  31

Required Equipment  ..........................................................................................................................  31

A/D Calibration (For DI-720, DI-722, and DI-730 Series Instruments)  ....................................  31
D/A Calibration (DI-720 Instruments Only) ...............................................................................  31

A/D Calibration Verification (DI-720, DI-722, and DI-730 Series Instruments)  .............................  31
D/A Calibration (DI-720 Series Only)  ..............................................................................................  32
Offset Calibration Verification (DI-720 and DI-722 Instruments Only)  ..........................................  33
Full Scale (Span) Calibration Verification (DI-720 and DI-722 Instruments Only) .........................  33
Offset Calibration Verification (DI-730 Instruments only) ...............................................................  34
Full Scale (Span) Calibration Verification (DI-730 Instruments Only)  ............................................  34

6. Block Diagram .....................................................................................................................................   35

DI-720 Series  .....................................................................................................................................  35
DI-722 Series  .....................................................................................................................................  36
DI-730 Series (Analog Input)  ............................................................................................................  37
Ethernet Instruments ..........................................................................................................................  38

Содержание DI-725/E













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды