Datakom D-500 MK2 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 197

background image

D-500 MK2 User Manual Firmware V-6.3

- 84 -

The TEST mode is entered by pressing the

button.

The TEST mode is used in order to test the genset under load.

Once this mode is selected, the engine will run as described in the AUTO mode, regardless of the mains
availability and the load will be transferred to the genset.

The genset will feed the load indefinitely unless another mode is selected.

▪

AMF Mode:

The controller will run the engine and make an interrupted transfer.

▪

Synchronizing & Load Sharing Mode:

The controller will run the genset. If the busbar is not

energized, it will simply close its genset contactor. If the busbar was energized then it will
synchronize to the busbar, get in parallel, ramp up and start sharing the load.

▪

ATS Mode:

The controller will activate its REMOTE START output, thus the genset group will run,

synchronize and close to the busbar. When sufficient power is ready on the busbar, the controller will
transfer the load.

14.5. TEST MODE

«
...
82
83
84
85
86
...
»

Содержание D-500 MK2






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D-500 MK2

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Lakeshore Страницы: 192

Бренд: QUAD Страницы: 16

Бренд: Hansen Страницы: 4

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: Maclaren Страницы: 43

Бренд: Lawler Страницы: 5

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: Full Gauge Controls Страницы: 3

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды