Datakom D-500 MK2 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 197

background image

D-500 MK2 User Manual Firmware V-6.3

- 140 -

Related parameters are:

Parameter Definition

Factory Set

Description

Network IP Address

0.0.0.0

This is the IPv4 (internet protocol version 4) address
that the unit will require from the DHCP (dynamic host
control protocol) server.
If this parameter is set to 0.0.0.0 then the unit will
require any IPv4 address from the DHCP server.
If you are not an IP professional please leave this
address as “0.0.0.0”.

Gateway IP Address

0.0.0.0

This is the router IPv4 address, If the Network IP
a

ddress and Gateway IP Address are set to “0.0.0.0”

then the unit will get the gateway address
automatically.
If you are not an IP professional please leave this
address as “0.0.0.0”.

Subnet Mask

255.255.255.0

Reserved for IP professionals.
If you are not an IP professional please leave this
address as “255.255.255.0”.

Modbus TCP/IP Port

502

Internal Modbus TCP/IP server’s port number. The unit
answers Modbus requests to this port only.

Modbus Address

1

This is the modbus controller identity used in Modbus
communication.

The ethernet connection status is monitored at ethernet screen page.

18. ETHERNET CONFIGURATION

Connection
status
indicator

IP address
of the unit,
assigned by
the network
switch

Data Receive
and Transmit
Indicators

«
...
138
139
140
141
142
...
»

Содержание D-500 MK2






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D-500 MK2

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: FrSky Страницы: 2

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

Бренд: babyzen Страницы: 11

Бренд: LAS Страницы: 6

Бренд: Rain Bird Страницы: 138

Бренд: Vega Страницы: 20

Бренд: PUTCO Страницы: 2

Бренд: Trane Страницы: 72

Бренд: Objective Imaging Страницы: 11

Бренд: EFI Страницы: 127

Бренд: maxxess Страницы: 11

Бренд: SOLARJACK Страницы: 14

Бренд: National Instruments Страницы: 26

Бренд: ICP DAS USA Страницы: 7

Standard 22 GYRO COMPASS

Бренд: Raytheon Anschütz Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды