DataApex Clarity INT7 Скачать руководство пользователя страница 38

Страница: 38 / 42

INT7 A/D Converter

5 Troubleshooting

5.5 Data Acquisition - Simulated

▌ The title "Simulated" is displayed in the

Data Acquisition

window.

Fig 37: Data Acquisition Simulated

Description:

The corresponding Instrument only displays the simulated curve (from the file
CHANNX.DTA file) in the

Data Acquisition

window, or in other words has allocated

DEMO detector

on itself.

Solution:

Open the

System Configuration

dialog from the

Clarity

window using the

System -

Configuration...

command and check the tab of the corresponding Instrument -

Instrument X

. If it only has the detector signals from the

DataApex DEMO

detector, it is necessary to reconfigure it. You can find more information how to add
a detector in the chapter

"Clarity Configuration"

on pg

Make sure that you have installed a full version of

Clarity

. If this is not the case,

inscription

DEMO

is in the header of the main window. If so, install the full version

and enter the user code you have been provided. Also make sure that the detector
is properly configured.

- 34 -

Содержание Clarity INT7











































Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды

DataApex Clarity INT7, Руководство пользователя

Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды