DataApex Clarity INT7 Скачать руководство пользователя страница 32

Страница: 32 / 42

INT7 A/D Converter

5 Troubleshooting

5.3.3 Reinstallation of drivers in Windows 2000

Note:

Windows

2000

is supported until

Clarity

version

3.0

only.

After installing

Clarity

and the

INT7

device, the

Device Manager

either

does not display the

Chromatography Devices

–

INT7

item at all or it

displays a yellow exclamation mark next to the item that indicates that the
device is not working properly.

Fig 25: Device Manager in Windows 2000

If the "

DataApex Acquisition device, model 7.XX

" item is missing,

Windows has automatically installed incorrect driver.
If you are able to locate which device was mistakenly installed instead of
the

INT7

driver, you can open its

Properties

and

Update this driver

. In the

manual installation process, select the correct drivers analogically to the
description in the chapter

"Installing the correct driver manually"

on pg

If the correct driver cannot be determined, the last installed driver will have
to be removed.

Caution:

This procedure can be used safely only if you did not install any other
hardware since the installation of the converter.

5.3.3.1 Deleting incorrect *.INF files in the system

Note:

Be sure to have the

Clarity

software installed already.

Open the C:\WINNT\INF ( C:\WINDOWS\INF ) folder

①

Windows

Explorer

Note:

You may have to allow for the hidden system files to be displayed. In menu
select

Tools

–

Folder Options

View

tab then set the

Hidden Files and

Folders

option to

Show Hidden Files and Folders

- 28 -

Содержание Clarity INT7











































Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды

DataApex Clarity INT7, Руководство пользователя

Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды