DataApex Clarity INT7 Скачать руководство пользователя страница 13

Страница: 13 / 42

INT7 A/D Converter

3 Installation

The

DataApex INT7 Setup

dialog will appear.

Fig 5: DataApex INT7 Setup

Enter the detector names in

Name

fields for individual channels, set signal

units.

Note:

A detailed description of this dialog can be found in the chapter

"DataApex INT7 Setup"

on pg

Press the

button.

The

INT7

will appear in the

Setup Control Modules

list

④

of the

System

Configuration

dialog.

Drag and drop the

INT7

icon from the

Setup Control Modules

list

④

on the

left side of the

System Configuration

dialog to the desired

Instrument

⑤

tab on the right side

⑥

(or use the

button

⑦

to do so).

Set the

Ext. Start Dig. Input

and

Ready Dig. Output

numbers

⑧

for your

acquisition card according to the wires being used for synchronization.

Note:

The configuration dialog of the

INT7

card (

DataApex INT7 Setup

) can be

displayed any time by double-clicking on its icon or using the

Setup

button.

- 9 -

Содержание Clarity INT7











































Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды

DataApex Clarity INT7, Руководство пользователя

Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды