DataApex Clarity INT7 Скачать руководство пользователя страница 7

Страница: 7 / 42

INT7 A/D Converter

2 Requirements

2 Requirements

The

INT7

internal

PCI A/D converter

can be used with the

Clarity

software on PC’s using the OS described in the

Tab 1

on pg

The PC must have a free

PCI

slot for your

INT7

card.

Note:

Full size

PCI 2.0

, 32 bit PCI slot for 5V 32 bits half-length extension card is

required. Low profile or PCI Express slots cannot be used.

Tab 1: Hardware and Software Compatibility with supported Windows OS:

Software \ Windows

10**

8.1** / 7

SP1

Clarity

Yes (from 6.2)

Yes

Clarity Lite

Yes (from 6.2)

Yes

CSW32

Windows 8.1

(32 and 64-bit version) is supported from

Clarity

(

Lite

)

4.0.3

* From

Clarity

(

Lite

)

3.0

the

64-bit

OS is supported.

Tab 2: Hardware and Software Compatibility with obsolete Windows OS:

Software \ Windows

SP3

Vista

SP2

2000

Clarity

Yes
(until 7.4.1)

Yes
(from 3.0 to 7.2)

Yes
(until 3.0)

Clarity Lite

Yes
(until 7.4.1)

Yes
(from 3.0 to 7.2)

Yes
(until 3.0)

CSW32

Yes
(until 7.4.1)

Yes

* From

Clarity

(

Lite

)

3.0

the

64-bit

OS is supported.

- 3 -

Содержание Clarity INT7











































Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды

DataApex Clarity INT7, Руководство пользователя

Результаты поиска

Содержание Clarity INT7

Отзывы:

Похожие инструкции для Clarity INT7

Бренды по названию

Популярные бренды