DataApex Agilent 7890 Скачать руководство пользователя страница 34

Страница: 34 / 39

Agilent 7890

4 Using the control module

4.8.3 Signals tab

Fig 19: Agilent 7890 Setup - Signals

This tab defines the number of signals that will be processed by

Clarity

Count

Defines the number of signals received by

Clarity

. These signals

correspond to

Clarity

detectors and will have their own sub-tabs in the

Method Setup - Acquisition

dialog, if configured on the given

Clarity

Instrument.

Signal 1 (..4)

Sets the name of the particular signal.

This Device Starts the Run in Clarity / Clarity Starts This Device

This radiobutton enables to start the analysis run from the

Clarity

. With

This Device Starts the Run in Clarity

checked, the device is started prior to

Clarity

by its front button or autosampler connected to this device and

passes the start to

Clarity

. When

Clarity Starts This Device

is checked,

Clarity

is started prior to this device by separately wired autosampler,

Start button in Single Run or different device and then starts this device.

Note:

The

This Device Starts the Run in Clarity

option is checked by default.

- 30 -

Содержание Agilent 7890








































Результаты поиска

Содержание Agilent 7890

Отзывы:

Похожие инструкции для Agilent 7890

Бренды по названию

Популярные бренды

DataApex Agilent 7890, Руководство пользователя

Результаты поиска

Содержание Agilent 7890

Отзывы:

Похожие инструкции для Agilent 7890

Бренды по названию

Популярные бренды