DataApex Agilent 7890 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 39

background image

4 Using the control module

Clarity Controls

4.3.2 Front (Back) Inlet

Fig 8: Method Setup - GC - Inlet

This tab governs the settings concerning the inlets of the

Agilent 7890

chromatograph. According to configuration of particular chromatograph,
there can be

Front Inlet

or

Back Inlet

tabs, both with the same appearance.

Particular fields may vary, according to the type of the inlet set.

Temperature Mode

Defines the temperature mode for the inlet. Available for COC and PTV
inlets.

Carrier Gas

Sets the type of carrier gas used on this GC.

Temperature Gradient Table

Allows to edit temperature ramp for the inlet (up to three rates and
plateaus). Available for COC and PTV inlets.

Injection Pulse (Press + Time)

Sets the pressure and duration of pressure pulse during injection of the
sample. Available for PTV and Split/Splitless inlets.

Pneumatic Mode

Defines the operation mode for the injector port. Available for PTV and
Split/Splitless inlets.

Total Flow

Turns on/off and sets the flow rate for carrier gas. The value entered here
is used only when there are no columns defined on the GC, however the

- 13 -

«
...
15
16
17
18
19
...
»

Содержание Agilent 7890








































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 7890

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Gate Motors Страницы: 6

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: Parker Страницы: 28

Бренд: Rain Bird Страницы: 20

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Osaka Страницы: 12

Бренд: Delta Страницы: 16

Бренд: Veichi Electric Страницы: 8

R1000 series E20

Бренд: Roland Страницы: 156

Бренд: Bandini Industrie Страницы: 42

Бренд: FOR-A Страницы: 6

Бренд: turck Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды