background image

 5 

• 

DO NOT

 operate the stove if the flame becomes dark and sooty or if the firepot overfills with pellets.  Push 

the 

OFF

 Touch Pad and inspect the heater.  (See Operating Your Stove). Soot or creosote may accumu-

late in the exhaust vent system when the stove is operated under incorrect conditions such as an ex-
tremely rich burn. The flame will have a lazy orange color with black tips. This indicates poor pellet fuel 
combustion. 

• 

NEVER

 block free airflow through the open vents of the unit. The viewing door and ash pan must be 

closed and latched during operation.  

• 

The pellet appliance exhaust system works with 

negative

 combustion chamber pressure and a 

positive

 

chimney pressure, therefore the exhaust system must be completely airtight and properly installed. All 
exhaust system vent joints must be sealed, gas tight,  with HI-TEMP RTV silicone sealant, and/or at least 
3 sheet metal screws 

per joint

 

and to the heater

 also. 

• 

Your heater requires periodic maintenance and cleaning (Refer to ”Routine Cleaning” section of the    
manual). Failure to maintain your heater may lead to smoke spillage in your home.  

• 

Disconnect

 the power cord from the electrical outlet before performing any maintenance.  Pushing ”OFF” 

Touch Pad does not disconnect all power to the heater. 

• 

BEFORE 

carrying out any maintenance or cleaning, allow the heater to cool. Ashes must be disposed in a 

metal container with a tight lid and placed on a non-combustible surface or on the ground, well away from 
all combustible materials, pending final disposal.  

• 

The exhaust system should be checked twice a year minimum for any build-up of soot or  
creosote. Do not touch the hot surfaces of the heater.  

S

S

AFETY

AFETY

 

 

T

T

ESTING

ESTING

 

NOTE:  Canadian Comfort Industries grants no warranty, implied or stated, for the installation or  
            maintenance of your appliance, and assumes no responsibility of any consequential damage(s). 

In accordance with the procedures and specifications listed in UL1482 – 1998 & ASTM E 1509-04, and  
ULC-S627-00 and ULC-S628-M93 for solid fuel room heater.  Tested and listed for use in Manufactured 
Homes in accordance with Oregon Administrative Rules 814-23-900 through 814-23-909. The Canadian   
Comfort  Industries pellet stove has  been independently tested and listed by INTERTEK (an accredited testing                       
laboratory) to UL, ULC and CSA standards. It is tested and listed for residential installation according to current 
national and local building codes as: 

 

• 

A Freestanding Room Heater

 

• 

A Fireplace Insert

 

• 

A Built-in Insert

 

• 

A Hearth Stove

 

• 

A Mobile Home Heater.

 

 

The Safety Listing Label is located on the rear  
inspection panel for model CCGB1 and CCGB2. 
Please read the label carefully.  
It contains important information  
about installation and operation of your  
pellet appliance.  

 

Note that your STOVE’S serial number is located 
on the safety label. Your appliance serial 
Number is preceded by a “WH-“ 
 (example WH-00000). 
(see diagram) 

Glow Boy  Pellet & Biomass             

               www.glowboystoves.com               5 

 

Содержание GLOW BOY FGB









































Отзывы: