background image

 38 

T

T

ROUBLE

ROUBLE

 

 

S

S

HOOTING

HOOTING

  

   

PROBLEM 

CAUSE 

SOLUTION 

Fire burns with a yellow 
flame.  Fuel builds up in 
the burn grate. Window 
gets real dirty quickly. 

1. Insufficient combustion air.  *Adjust the air inlet damper. 

*Check for blockage of air intake both inside as 
well as outside. 
*Confirm proper placement of burn grate. 
*Inspect and clean burn grate. 

 

2. Fuel  

*Inspect fuel for amounts of fines and debris. 
*Change to dry clean fuel. 
*Use high quality premium grade fuel.  
*Adjust or fine tune feed rates. 

 

3. Air Leaks 

*Ensure glass and gasket seated properly 
*Ensure door is close and latched securely 
*Check ash pan and gasket, secure and tight. 

 

4. Combustion Fan 

*Check and clean ash build up on fan propellers 
and exhaust intakes and venting. 
*Check for blockages. 
*Check for proper voltage to the stove 
*Replace defective part and gasket. 

 

5. Exhaust System 

*Check for blockage, ash build. 
*Inspect vent cap and clean out tee. 
*Too many elbows, to long of run, or change size 
*Protect venting from extreme weather elements. 

Smoke or smoke smell 
spillage. 

1. Exhaust System 

*Hi-Heat RTV silicone all joints even  
manufactured.  Ensure venting is gas tight. 
*Inspect exhaust fan and gasket area, ensure a 
tight fit 
*Proper maintenance and cleaning. 

 

2. Over Feeding.  Fuel over-
filling burn grate 

*Check air inlet damper for proper setting. 
*Adjust feed rate to lower level 

The stove keeps going 
out. 

 

1.Fresh unburned fuel or  
powder like ash build up in 
the grate. 

*Check air inlet damper, may need more air. 
*Fine tune feed rate, to lower amount of fuel 
*Ensure good quality day fuel supply.   
*Proper maintenance and cleaning. 

 

2.No fuel or ashes found in  
The burn grate 

*Adjust air inlet damper to reduce amount of air 
to burn grate.  Exhaust temperature to low and 
temperature disk is turning off stove.  
*Adjust control to increase fuel feed rate. 

The stove will not shut 
off. 

 

1.Control 

*Press OFF touch pad, the stove will continue to 
run for 30 minutes after the exhaust has cooled 
properly 
*Confirm mode of operation 

 

2.Wall Thermostat 

*Ensure wall thermostat is turn down below the 
room temperature.(Thermostat On/Off Mode) 
*Unit will not shut off in the (Thermostat Low/
High mode). You must press the OFF touch pad. 

Glow Boy  Pellet & Biomass              

               www.glowboystoves.com               38 

 

Содержание GLOW BOY FGB









































Отзывы: