manualshive.com logo in svg

Danfoss VLTAutomationDrive FC 360, Быстрое руководство

Поделиться
Скачать
Danfoss VLTAutomationDrive FC 360 Скачать руководство пользователя страница 46

8.3  Fuse Specifications

8.3.1 Fuses 

It is recommended to use fuses and/ or circuit breakers on
the supply side as protection in case of component break-
down inside the frequency converter (first fault).

NOTE

This is mandatory in order to ensure compliance with IEC
60364 for CE or NEC 70 for UL.

WARNING

Personnel and property must be protected against the
consequence of component break-down internally in the
frequency converter.

Branch Circuit Protection
In order to protect the installation against electrical and
fire hazard, all branch circuits in an installation, switch
gear, machines etc., must be protected against short-circuit
and over-current according to national/international
regulations.

NOTE

The recommendations given do not cover Branch circuit
protection for UL.

Short-circuit protection
Danfoss recommends using the fuses/Circuit Breakers
mentioned below to protect service personnel and
property in case of component break-down in the
frequency converter.

8.3.2 Recommendations

WARNING

In case of malfunction, not following the recommendation
may result in personnel risk and damage to the frequency
converter and other equipment.

The following tables list the recommended rated current.
Recommended fuses are of the type gG for small to
medium power sizes. For larger powers, aR fuses are
recommended. For Circuit Breakers, Moeller types have
been tested to have a recommendation. Other types of
circuit breakers may be used provide the limit the energy
into the frequency converter to a level equal to or lower
than the Moeller types.

If fuses/Circuit Breakers according to recommendations are
chosen, possible damages on the frequency converter will
mainly be limited to damages inside the unit.

For further information please see Application Note 

Fuses

and Circuit Breakers

, MN90T

Specifications

VLT

®

 AutomationDrive FC 360 Quick Guide

42

MG06A102 - VLT

®

 is a registered Danfoss trademark

8

8

Содержание VLTAutomationDrive FC 360





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды