![background image](http://html1.mh-extra.com/html/danfoss/vltautomationdrive-fc-360/vltautomationdrive-fc-360_quick-manual_507919026.webp)
4.3 Main Menu
The Main Menu gives access to all parameters.
1.
To enter the Main Menu, press [Menu] key until
indicator in display is placed above
Main Menu
.
2.
[
▲
] [
▼
]: browse through the parameter groups.
3.
Press [OK] to select a parameter group.
4.
[
▲
] [
▼
]: browse through the parameters in the
specific group.
5.
Press [OK] to select the parameter.
6.
[
►
] and [
▲
] [
▼
]: set/change the parameter value.
7.
Press [OK] to accept the value.
8.
To exit, press either [Back] twice (or three times
for array parameters) to enter
Main Menu
, or
press [Menu] once to enter
Status
.
The principles for changing the value of continuous,
enumerated and array parameters, respectively, are shown
below.
130BC446.10
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
1
2
3
4
5
6
7
10
11
12
OK
OK
Back
8
Back
Setup 1
2 x
+
OK
9
OK
Illustration 4.5 Main Menu Interactions - Continuous Parameters
1
[OK]: the first parameter in the group is shown.
2
Press [
▼
] repeatedly to move down to the desired
parameter.
3
Press [OK] to start editing.
4
[
►
]: first digit flashing (can be edited).
5
[
►
]: second digit flashing (can be edited).
6
[
►
]: third digit flashing (can be edited).
7
[
▼
]: decreases the parameter value, the decimal point
changes automatically
8
[
▲
]: increases the parameter value.
9
[Back]: cancel changes, return to 2)
[OK]: accept changes, return to 2)
10 [
▲
][
▼
]: select parameter within the group.
11 [Back]: Removes the value and shows the parameter group.
12 [
▲
][
▼
]: select group.
Table 4.4
For enumerated parameters the interaction is similar but
the parameter value is shown in brackets, because of the
NLCP digits limitation (4 large digits) and the enum can be
greater than 99. When the enum value is greater than 99,
the NLCP can only display the first part of the bracket.
130BC447.11
Setup 1
Setup 1
Setup 1
1
2
3
4
5
6
OK
OK
Back
7
OK
Back
Illustration 4.6 Main Menu Interactions - Enumerated Parameters
1
[OK]: the first parameter in the group is shown.
2
Press [OK] to start editing.
3
[
▲
][
▼
]: change parameter value (flashing).
4
Press [Back] to cancel changes or [OK] to accept changes
(return to screen 2).
5
[
▲
][
▼
]: select parameter within the group.
6
[Back]: Removes the value and shows the parameter group.
7
[
▲
][
▼
]: select group.
Table 4.5
User Interface and Programm...
VLT
®
AutomationDrive FC 360 Quick Guide
22
MG06A102 - VLT
®
is a registered Danfoss trademark
4
4
Содержание VLTAutomationDrive FC 360
