Danfoss VLTAutomationDrive FC 360 Скачать руководство пользователя страница 38

Страница: 38 / 52

7 Basic Troubleshooting and FAQs

7.1 Start Up and Operation

Symptom

Possible Cause

Test

Solution

Motor not running

LCP Stop

Check if [Off] has been pressed.

Press [Auto On] or [Hand On]
(depending on operation mode) to
run the motor.

Missing start signal (Standby)

Check

5-10 Terminal 18 Digital Input

for correct setting for terminal 18
(use default setting).

Apply a valid start signal to start
the motor.

Motor coast signal active
(Coasting)

Check

5-12 Coast inv

. for correct

setting for terminal 27 (use default
setting).

Apply 24V on terminal 27 or
program this terminal to

operation.

Wrong reference signal source

Check reference signal: Local,
remote or bus reference? Preset
reference active? Terminal
connection correct? Scaling of
terminals correct? Reference signal
available?

Program correct settings. Check

3-13 Reference Site

. Set preset

reference active in parameter
group

3-1* References

. Check for

correct wiring. Check scaling of
terminals. Check reference signal.

Motor running in wrong
direction

Motor rotation limit

Check that

4-10 Motor Speed

Direction

is programmed correctly.

Program correct settings.

Active reversing signal

Check if a reversing command is
programmed for the terminal in
parameter group

5-1* Digital inputs.

Deactivate reversing signal.

Wrong motor phase connection

See in this manual.

Motor is not reaching
maximum speed

Frequency limits set wrong

Check output limits in

4-14 Motor

Speed High Limit [Hz]

and

4-19 Max

Output Frequency

Program correct limits.

Reference input signal not scaled
correctly

Check reference input signal
scaling in

6-* Analog I/O mode

and

parameter group

3-1* References.

Program correct settings.

Motor speed unstable

Possible incorrect parameter
settings

Check the settings of all motor
parameters, including all motor
compensation settings. For closed
loop operation, check PID settings.

Check settings in parameter group

1-6* Analog I/O mode

Motor runs rough

Possible over-magnetization

Check for incorrect motor settings
in all motor parameters.

Check motor settings in parameter
groups

1-2* Motor data, 1-3* Adv

motor data

, and

1-5* Load indep.

setting.

Motor will not brake

Possible incorrect settings in the
brake parameters. Possible too
short ramp down times.

Check brake parameters. Check
ramp time settings.

Check parameter group

2-0* DC

brake

and

3-0* Reference limits

Basic Troubleshooting and F...

VLT

AutomationDrive FC 360 Quick Guide

MG06A102 - VLT

is a registered Danfoss trademark

Содержание VLTAutomationDrive FC 360





















































Результаты поиска

Содержание VLTAutomationDrive FC 360

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLTAutomationDrive FC 360, Быстрое руководство

Результаты поиска

Содержание VLTAutomationDrive FC 360

Отзывы:

Бренды по названию

Популярные бренды