Danfoss VLTAutomationDrive FC 360 Скачать руководство пользователя страница 14

Страница: 14 / 52

3 Installation

3.1 Mechanical Installation

Select the best possible operation site by considering the
following:

•

Ambient operating temperature

•

Installation method

•

How to cool the unit

•

Position of the frequency converter

•

Cable routing

•

Power source supplying correct voltage and
necessary current

•

Motor current rating within the maximum current
from the frequency converter

•

Correct rating of external fuses and circuit
breakers

Cooling and Mounting:

•

Top and bottom clearance for air cooling must be
provided, see

Table 3.1

for clearance requirements

•

Derating for temperatures starting from 45

C and

elevation 1000m above sea level must be
considered. See the equipment Design Guide for
detailed information.

Enclosure

J1-J5

J6/J7

Clearance above and below the

unit [mm]

100-200

Table 3.1 Minimum Airflow Clearance Requirements

•

Mount the unit vertically

•

IP20 units (but NOT IP21 units) allow side by side
installation

•

Improper mounting can result in over heating
and reduced performance

•

Use the slotted mounting holes on the unit for
wall mounting, when provided

•

See

8.4 Connection Tightening Torques

for proper

tightening specifications.

Installation

VLT

AutomationDrive FC 360 Quick Guide

MG06A102 - VLT

is a registered Danfoss trademark

Содержание VLTAutomationDrive FC 360





















































Результаты поиска

Содержание VLTAutomationDrive FC 360

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLTAutomationDrive FC 360, Быстрое руководство

Результаты поиска

Содержание VLTAutomationDrive FC 360

Отзывы:

Бренды по названию

Популярные бренды