Danfoss pved-cl Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 116

Danfoss pved-cl Скачать руководство пользователя страница 78

Ve

Vehicle

speed

Xstl - Joystick

signal

Qm,Lx,db

10 ms

100 ms

Ramp

function

Steering

sensitivity

SseSts0,Sts1,Sts2,

Sts3,Sts4,Sts5, Vesm

Ve -Vehicle

speed

100 ms

10 ms

Yact - Actuator

position

Transfer

function

Sr, Lr, Tro, Tfo, Lf,

Trh, Tfh, YsetFr, Tfr,

TAbortDownRamp,

Tra, Verm

Yact

Actuator

position

Q

Port flow

command

Soft
stop

Cf, Off

Yr,Yl

10 ms

P005 207E

Acquire the Signals
See

Mapping a Steering Device

on page 31 on how to map the steering wheel sensor and steering wheel

angle sensor.

Set-point Transfer Function

The transfer function provides 3 parameters to transfer joystick inputs signal to requested port flow.

1000

1000

-1000

-1000

750

500

250

-500

-750

-250

-750

-500

-250

250

500

750

Saturation

Saturation

Defaults

db=50, Lx=0

Qm =1000

Sts=105

Qm

Lx

db

CL - port

CR - port

Sts

Example

db=100, Lx=10

Qm= -750

Sts=116

Xstl - input signal:

1 unit = 0.1% of

Max activation

Max input signal
for activating the
steering device
into the right
direction or CW

Max input signal
for activating the
steering device
into the left
direction or
CCW

Qr - r

equest

ed p

or

t flo

w

: 1

unit = 0.1% of M

ax p

or

t flo

w

P005 210E

Db Sets a dead-band in the middle region of the steering input. It prevents self-steering caused by
manufacturing deviations in the signal when the handle is in the middle or released position.

The default value is set twice the maximum deviation of most spring returned steering devices.
Lx Effect the inherent linearity between steering actuator speed and steering angle. The set value is set
down when slower cylinder speed at larger steering angles is required.

The default value will not effect the resulting relation.
Qm Limits the maximum cylinder speed for steering the vehicle in the right steering direction. (See set-
point transfer function above)

The default value is set equal to the inherent max port flow capacity of the valve and will therefore not
have any effect.

Operation Manual

PVED-CL Controller for Electro-Hydraulic Steering, Version 1.38

Steering by Low Priority Steering Device – Open Loop

78 |

©

Danfoss | May 2016

11025583 | AQ00000216en-US0302

«
...
76
77
78
79
80
...
»

Содержание pved-cl





















































































































Отзывы:

Нет отзывов