Danfoss pved-cl Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 116

Danfoss pved-cl Скачать руководство пользователя страница 18

The program parameters are organized in a matrix. Each program parameter index for given program
and for a given steering device can be derived as follows:
Parameter index = [Steering Device number][Program index][Program parameter sub-index]

Number of programs per steering device

Steering device

Steering Device Number

Program Index

Steering wheel sensor (SASA)

1

0-9

High priority steering device

3

0-4

Low priority steering device

4

0-4

High priority set-point controller

5

0-4

The program parameter sub-index is the two last digits in program parameters in appendix

on page 112.

What is the program parameter index for ‘Steering sensitivity selector, Sse’ for the steering wheel
program 4?

Sse

Steering wheel device is defined as device number 1. The index for program number 4 is derived by
substituting x with 4 i.e. the index is 1409.
Sse for high priority steering device program 1 is 3109 etc.

Default program index for steering devices is 0.

Reading and Writing Parameters

Configuring the PVED-CL by means of setting parameters and reading parameters is done via a J1939
CAN bus, using proprietary PGN 61184. The configuration command set is described in

PVED-CL

Communication Protocol

, 11079551.

Operation Manual

PVED-CL Controller for Electro-Hydraulic Steering, Version 1.38

Configuration and Adjustment

18 |

©

Danfoss | May 2016

11025583 | AQ00000216en-US0302

«
...
16
17
18
19
20
...
»

Содержание pved-cl





















































































































Отзывы:

Нет отзывов