Danfoss pved-cl Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 116

Danfoss pved-cl Скачать руководство пользователя страница 60

Steering by High Priority Steering Device – Open Loop

EHPS Type 2 System Diagram

Q

Steering
cylinder

EHPS Valve

Automatic steering

OSP

PVE

Steering angle sensor

Position

sensor

P005 225E

Vehicle speed

Joystick or mini wheel

Steering

cylinder

EHPS valve

OSP

PVE

Q

High

priority

Functionality Tree

The tree below illustrates the availability of the PVED for steering by joystick, mini wheel with speed
output or by potentiometer-like steering devices. The manufacturing default functionality is found by
following the red line. Following the instructions in this chapter can of course modify the default. The
switches in the tree are used to select the functionality required. In case different functionalities are
required, the EHPS software provides 5 programs from which the driver can select when the system is
fully operative.

P005 202E

Open loop, fixed sensitivity, with no ramps
applied.

Closed loop, fixed sensitivity

Closed loop
Cp=255

Related to

vehicle speed

Sse=3

Fixed

Sse=1

Open loop, fixed sensitivity, with fixed ramp times,

Fixed

Sse=1

Related to
position of

steering actuator

Sse=2

Related to

vehicle speed

Sse=3

Open loop, sensitivity related to steering actuator
position, with fixed ramp times

Open loop, sensitivity related to steering actuator
position, no ramps applied

Open loop, sensitivity related to vehicle speed,
with fixed ramp times

Open loop, sensitivity related to vehicle speed,
no ramp times applied

Open loop

Cp=0

Fixed

Sr=1

Var

Sr=2

C

on

tr

ol pr

inciple swit

ch

Sensitivit

y swit

ch

R

amp swit

ch

Open loop, fixed sensitivity, with variable ramp
times as function to vehicle speed,

Open loop, sensitivity as function to steering actuator
position, with variable ramp times related to vehicle
speed,

Open loop, sensitivity related to vehicle speed,
with ramp times related to vehicle speed

Closed loop, sensitivity related to vehicle speed,

switches

No signal (0)

CAN (255)

C

hannel mapping swit

ch

Cp

Sse

Sr

No,

Sr=0

default

Fixed

Sr=1

Var

Sr=2

No,

Sr=0

Fixed

Sr=1

Var

Sr=2

No,

Sr=0

* Sensitivity means: number of revolutions on steering wheel from lock to lock

*

Y=0

1

2

3

4

Program number: Y

Select the Control Principle

The PVED-CL provides open loop control for steering devices with spring return or for steering devices
with a speed output,. This control principle keeps a fixed or variable relation between steering input and
cylinder speed. The control loop provides several parameters to transform positional information to port
flow.
Cp selects the open-loop control using parameter index 3y02 equal to 0 (default). Y selects the program
and ranges from 0 and 9.

Operation Manual

PVED-CL Controller for Electro-Hydraulic Steering, Version 1.38

Steering by High Priority Steering Device – Open Loop

60 |

©

Danfoss | May 2016

11025583 | AQ00000216en-US0302

«
...
58
59
60
61
62
...
»

Содержание pved-cl





















































































































Отзывы:

Нет отзывов