Danfoss MCX08M страница 52 Скачать руководство пользователя

Страница: 52 / 72

DKRCC.PS.RI.A1.02 / 520H4358 - Air Handling Seq. user manual - V 2.2

Produced by Danfoss Electronics spa Graphic Department, 10-2009

Danfoss Electronics spa

Air Handling seq.

- user manual

Fig 48_ [Supply and return fans - Type of supply fans]

If F00=PID, the fan modulates its speed with PID control (parameters Fr3-Fr6) according to a setpoint Fr2

and the value of a control probe, defined by F01 from among the return temperature (F01=REt), supply

temperature (F01=SUP) and air pressure “bAR – Air Pressure” (F01=bAR) probes.

The control type is defined in Fr1 from among the following possibilities:

Fr1=INV. Inverse control, i.e. heating.
Fr1=DIR. Direct control, i.e. cooling.
Fr1=CO1. Direct or inverse control according to the operating mode: summer/winter. Direct in summer,

inverse in winter.
Fr1=CO2. Direct or inverse control according to the operating mode: summer/winter. Inverse in summer,

direct in winter.

The outputs indicated in the previous point are used to control the fan.

Note that the fan is never stopped if temperature or humidity control action is requested. In this case the

fan is set to its minimum speed.

In case of a reference probe failure, the fan is forced to its maximum speed.

Return fan output

As with the supply fan, the outputs used to control the return fan are the digital outputs “REF - Return Fan”, “RFL - REt.

Fan Low Sp.”, “RFH - REt. Fan High Sp” and the analog output “REF - Return Fan”.

•
•
•

•

Содержание MCX08M









































































Результаты поиска

Содержание MCX08M

Отзывы:

Похожие инструкции для MCX08M

Бренды по названию

Популярные бренды

Danfoss MCX08M, Руководство пользователя

Результаты поиска

Содержание MCX08M

Отзывы:

Похожие инструкции для MCX08M

Бренды по названию

Популярные бренды