Operating guide | iSave 50 - 70
6
180R9357 | AQ265943679828en-00100
2
IOM iSave 50 - 70 | 0
3
.202
3
3.
Safety
3.1 General
The iSave must not be used for other
purposes than those recommended and
specified without first consulting your local
iSave distributor.
This manual must be read and completely
understood by the responsible specialist
personnel prior to installation and
commissioning.
Use of this manual does not relieve operation
and maintenance personnel of the responsibility
of applying normal good judgment in the
operation and care of this product and its
components.
This manual must be available to all personnel
concerned at the site at all time.
An iSave must always be installed and used
in accordance with existing national and local
sanitary and safety regulations and laws. It is the
responsibility of the safety officer or the chief
operator to assure compliance with all local
regulations that are not taken into account in this
manual.
The iSave is a rotating machine that typically
operates at high pressure.
3.2 Intended use
The iSave is designed for use as energy recovery
device in Sea Water Reverse Osmosis (SWRO) or
Brackish Water Reverse Osmosis (BWRO) system.
The iSave must not be used for other purposes
than recommended and quoted for without
consulting your local iSave distributor.
3.3 Application range
For application range see data sheet 521B1378
available in appendix 10.1.
Always wear suitable safety and lifting
equipment when handling the iSave.
•
Bolt the iSave properly to the base before
start-up to avoid personal injury and/or
damage to the iSave.
•
The pipe connections to the iSave must be
stress-free mounted, securely fastened to
the iSave and well supported. Improper
installation will or could result in personal
injury and/or damage to the iSave.
•
Proper installation and care of shutdown
devices and over-pressure protection
equipment is essential.
•
All electrical installation work must be
carried out by authorised personnel in
accordance with EN60204-1 and/or local
regulations.
•
Install a lockable circuit breaker to avoid
inadvertent starting. Protect the motor and
other electrical equipment from overloads
with suitable
•
equipment.
•
The electric motors must be supplied with
adequate cooling ventilation.
•
Improper installation can cause fatal
injuries.
•
The iSave must not operate outside the
application range.
•
During the initial start-up, slowly raise the
pressure of the system and adjust the
over-pressure protection equipment for
proper limit settings.
•
Make sure that the pressure is released
from the iSave before the iSave is
disconnected from any pipe or hose
connections.
•
Make sure that the iSave can be drained
without injuring anyone and without
contaminating nearby equipment or the
environment.
•
Before intervening in the iSave/system,
the power must be shut off and the
starting device must be locked. When
intervening in the iSave unit, follow the
instructions for Service/Maintenance,
chapter 8.
•
A failure not to follow the instructions can
result in personal injury and/or damage to
the iSave. It will also invalidate the
warranty.
•
The iSave must never run dry. Dry running
produces heat and will cause damage to
internal parts.
•
If the iSave does not function satisfacto-
rily, contact your local iSave distributor.
Use of this manual does not relieve
operation and maintenance personnel of
the responsibility of applying normal
good judgment in the operation and care
of this product.
Applications not suitable for the iSave
can cause damages to the iSave unit,
with risk of personal injury.
Содержание iSave 50
