Danfoss iSave 50 Скачать руководство пользователя

Страница: 49 / 92

Design guide

Start and stop of the SWRO with iSave unit

180R9357 | AQ265943679828en-00100

IOM iSave 50 - 70 | 0

.202

More than one day system shutdown

1. Run the “daily system shutdown” procedure.

2. Supply permeate water to the SWRO system

by using fresh water/permeate flush

connection..

3. When the pressure ”HP in” (10) is below 20

barg/ 290 psig start the iSave(s).

NB! If the pressure (10) in “HP in” drops

below 3 barg/43.5 psig, the sound will

change of the iSave. This is due to

cavitation. “HP in” pressure at 3 barg/43.5

psig is acceptable for less than 10 minutes

within a period of 6 hours. Run the iSave

at its minimum allowable speed during

this period to reduce cavitation.

4. Start the APP pump(s) in a period of 5 sec. by

using normal ramp-up settings.

5. Stop the APP pump(s) after 5 sec.

6. Run the iSave(s) until the TDS in the high-

pressure line is equal to the TDS in the low-

pressure line.

7. Stop iSave(s) and permeate water supply.

Media filter

Permeate

iSave

Flowmeter

VFD

HP in

HP out

VFD

HP in

HP out

VFD

Fresh water

permeate flush

Full flow

cleaning/CIP

Filter

3 micron

nominel

Filter

10 micron

absolut

Drain

VFD

LP in

Second stage filter:

If recommended housing design and cartridges are not used, a second stage filter is required

CIP

Содержание iSave 50





























































































Результаты поиска

Содержание iSave 50

Отзывы:

Похожие инструкции для iSave 50

Бренды по названию

Популярные бренды

Danfoss iSave 50, Руководство по эксплуатации

Результаты поиска

Содержание iSave 50

Отзывы:

Похожие инструкции для iSave 50

Бренды по названию

Популярные бренды