Dalsa Piranha 4 Color P4-CC-04K07T-00-R страница 43 Скачать руководство пользователя

Страница: 43 / 116

Piranha4 4K Color Camera User's Manual

Teledyne DALSA

03-032-20180-01

Description

Line Rate

Exposure Time

Trigger Source

(Sync)

Internal line rate and exp osu re tim e

Internal, p rogram m able

Internal p rogram m able

Internal

External line rate and exp osu re tim e

Controlled by EXSYN C

p u lse

External (EXSYN C)

External

EXSYN C p u lse controlling the line

rate. Program m ed exp osu re tim e

Controlled by EXSYN C

p u lse

Internal p rogram m able

External

Figure 15. Exposure controls

The p aram eters u sed to select the im aging m od es—trigger sou rces (sync), exp osu re tim e, and line rate—
are grou p ed together as the Cam era Controls.

Camera Controls

Parameter

Description

Line Rate (in H z)

Cam era line rate in H z. Only available w hen the start line trigger p aram eter is
d isabled (Trigger Mod e off).

Exp osu re Mod e

Set the operation mode for the camera‘s exposure.
Trigger Wid th or Tim ed . Trigger Wid th is only available w hen Trigger Mod e is
enabled .

Trigger Width

Uses the w id th of the cu rrent line trigger signal p u lse to control the exp osu re
d u ration.

Timed

The exp osu re d u ration tim e is set u sing the Exp osu re Tim e featu re and the
exp osu re starts w ith the Line Start event.

Exposure Time Selector

Internally generated . Allow s for an ind ep end ent exp osu re tim e to be ap p lied to
each ind ivid u al color.

Exp osu re Tim e

Sets the exp osu re tim e (in m icrosecond s). Exp osu re Mod e featu re m u st be set
to Tim ed

All manuals and user guides at all-guides.com

Содержание Piranha 4 Color P4-CC-04K07T-00-R





















































































































Результаты поиска

Содержание Piranha 4 Color P4-CC-04K07T-00-R

Отзывы:

Похожие инструкции для Piranha 4 Color P4-CC-04K07T-00-R

Бренды по названию

Популярные бренды

Dalsa Piranha 4 Color P4-CC-04K07T-00-R, Руководство пользователя

Результаты поиска

Содержание Piranha 4 Color P4-CC-04K07T-00-R

Отзывы:

Похожие инструкции для Piranha 4 Color P4-CC-04K07T-00-R

Бренды по названию

Популярные бренды