Dalsa Piranha 2 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 86

background image

16

Piranha 2 User’s Manual

03-032-00493-14

Teledyne DALSA

!

Hirose 6-pin Circular M

ale

5

4

6

2

3

1

Mating Part: HIR

OS

E

HR10A-7P-6S

Pin Description

Pin

Description

1

+12V to +15V

4

GN D

2

+12V to +15V

5

GN D

3

+12V to +15V

6

GN D

2.4 Power Supplies

The cam era requ ires a single voltage inp u t (+12V to +15V). The cam era m eets all
p erform ance sp ecifications u sing stand ard sw itching p ow er su p p lies, althou gh w ell -
regu lated linear su p p lies p rovid e op tim u m p erform ance. See the Perform an ce
Sp ecifications for cu rrent requ irem ents.

When setting u p the cam era’s p ow er su p p lies follow these gu id elines:

•   Protect the camera with a fast-blow fuse between power supply and camera.
•   Do not use the shield on a multi-conductor cable for grou nd.
•   Keep leads as short as possible to reduce voltage drop.

See section 1.3 for p ow er requ irem ents.

WARNING: It is extremely important that you apply the appropriate voltages to your camera.

Incorrect voltages will damage the camera. Protect the camera with a fast-blow fuse between

power supply and camera.

Visit http :/ / vfm .d alsa.com for a list of com p anies th at m ake p ow er su p p lies th at m eet
the camera’s requirements. The companies listed should not be considered the only
choices. Many high qu ality su p p lies are available from other vend ors. We assu m e no
resp onsibility for the u se of these su p p lies.

2.5 Control Inputs, Camera Link

The cam era accep ts control inp u ts throu gh the Cam era Link MDR26F connector.

All inputs are optional. The camera ships in exposure mode 2 and with a 5 kHz line rate. All
Camera Control (CCx) signals are in a logic HIGH state.

Line rate can be set internally u sing the serial interface. Pow er -on rate is alw ays 9600
bau d . Data rate for the 40MH z m od el is alw ays 40MH z. Data rate for the 30MH z m od el is
alw ays 30MH z.

The external control sign als, EXSYN C an d PRIN , are op tional and enabled th rou gh the
serial interface.

PRIN

PRIN is an op tion al inp u t signal u sed for exp osu re control (PRIN ).

PRIN

Indicates

H igh

Integration

Low

Pixel reset

IMPORTANT:

This camera uses the

falling

edge of EXSYNC

to trigger line readout,

unlike previous DALSA

cameras, which used the
rising edg

e.

All manuals and user guides at all-guides.com

all-guides.com

«
...
14
15
16
17
18
...
»

Содержание Piranha 2 Series























































































Отзывы:

Нет отзывов

Похожие инструкции для Piranha 2 Series

Multi Gas Clip Simple Plus

Бренд: Gas Clip Technologies Страницы: 20

Бренд: Hama Страницы: 60

Бренд: Vaisala Страницы: 7

Бренд: CleverMic Страницы: 35

Wattstopper FS-555

Бренд: LEGRAND Страницы: 12

Бренд: Foscam Страницы: 70

Бренд: IP Camera Страницы: 37

Бренд: IntelliSense Страницы: 2

Бренд: ESYLUX Страницы: 16

Бренд: Icare Страницы: 27

Бренд: GST Страницы: 2

NightVision BulletCam

Бренд: Swann Страницы: 2

Бренд: Amcrest Страницы: 17

Бренд: Streamax Страницы: 8

Бренд: YOKOGAWA Страницы: 8

Бренд: V-TAC Страницы: 10

Бренд: Zee Страницы: 13

Бренд: Inovonics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды