Daktronics BA-1018 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 216

background image

Route power and signal cables into the scoreboard from the rear. There are two
knockouts for conduit connection in the back. All power and signal wiring
terminates at the driver enclosure.

Drawings A-178197

and

A-178235

illustrate the

16- and 8-column drivers used in Daktronics outdoor LED scoreboards.

To gain access to the driver enclosure, open the access door or digit panel and
remove the cover from the enclosure. Refer to the component locations drawings for
the access location for the scoreboard.

Connect power and signal cables at the appropriate
locations on the driver enclosure panel, shown in

Drawings A-178197

and

A-178235

.

Figure 7: Power Terminal Block

The conventional power termination panel has been
eliminated from Daktronics outdoor scoreboards; the
power feeder circuit connects directly to a terminal
block in the driver enclosure, as shown in

Figure 7

.

The terminal block is located in the lower right corner
of the enclosure. Connect the power wires as shown in
the illustration. Refer to the driver engineering
drawings and to the schematics listed at the beginning
of this section for additional wiring details. The
schematics

include a detailed illustration of the power

termination.

Note:

Driver enclosures in some earlier Daktronics scoreboards included a 120 V

power receptacle. There is no 120 V receptacle in Generation III displays. If you
want power to operate the control console at the scoreboard for troubleshooting,
Daktronics recommends that you have the installation electrician provide a 120 V
outlet close to the disconnect box specifically for this purpose.

Route signal cabling to the signal surge arrestor card in the upper left corner of the
driver enclosure. The connections are labeled to permit easy installation. At the
Signal In terminal block on the PCB, connect the red signal wire to the positive
terminal, the black to the negative
terminal, and the shield (silver) wire to
the shield terminal.

Note:

It is important

that the shield wire is properly connected
to the shield terminal on the signal surge
arrestor card.

Figure 8

illustrates the

signal surge arrestor card and
connectors.

Figure 8: Signal Surge Arrestor Card

For signal cable, Daktronics
recommends, as a minimum, single-pair,
shielded cable, 22 AWG (Daktronics
part number W-1077). Two-pair shielded
cable (Daktronics part W-1234) is
preferred.

7-4

Electrical

Installation

«
...
49
50
51
52
53
...
»

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BA-1018

Бренд: QUIETON Страницы: 24

Бренд: Quest Engineering Страницы: 24

Бренд: Nauticam Страницы: 2

Бренд: 4B Страницы: 16

Бренд: Danfoss Страницы: 14

Odyssey II Series

Бренд: Dakota Digital Страницы: 3

Бренд: Waters Страницы: 21

Бренд: IFM Electronic Страницы: 16

Бренд: IFM Electronic Страницы: 6

Бренд: Nautronic Страницы: 7

Бренд: NAPCO Страницы: 16

Бренд: Parker Страницы: 2

Бренд: Park Tool Страницы: 2

Бренд: ParaZero Страницы: 17

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды