Daktronics BA-1018 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 216

background image

Section 8: Scoreboard Maintenance
and Troubleshooting

IMPORTANT NOTES

:

1. Disconnect power before doing any repair or maintenance work on the

scoreboard.

2. Permit only qualified service personnel to access internal display

electronics.

3. Disconnect power when not using the scoreboard.

Note

: For assistance in the maintenance of team name message centers or other optional

scoreboard message centers, please refer to

Section 9

or the service manual that accompanies

those units.

8.1 Cabinet

Specifications

Cabinets for the Daktronics outdoor LED scoreboards are constructed of heavy-
gauge aluminum. Exact dimensions and weights for each model are listed in the
chart in

Section 3

. Removable panels for digits and indicators and for component

access are detailed in each model’s component locations drawing, listed in

Section

4

.

8.2 Component Location and Access

For front-access scoreboards, all internal
electronic components and digits can be
reached by opening a face panel, an
access door or a digit panel on the front
of the display.

Figure 9: LED Digit Panel

Digit panels have been simplified on the
outdoor LED scoreboards. They are held
in place on the scoreboard face by an
offset flange across the top and by three
screws at the bottom, as shown in

Figure 9

. (Very large digits may have

additional screws across the bottom.)
Open the scoreboard with care. Hold the
digit panel in place by putting hand
pressure on it while removing the
screws, and carefully lift it from the
board, sliding it out and down.

Scoreboard Maintenance

8-1

«
...
52
53
54
55
56
...
»

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BA-1018

Бренд: Accent Страницы: 36

Бренд: Omron Страницы: 36

Бренд: MacDon Страницы: 2

Бренд: Panasonic Страницы: 132

EASA-PHONE KX-T30810

Бренд: Panasonic Страницы: 16

Бренд: Kargo Master Страницы: 6

Бренд: OBH Nordica Страницы: 28

Бренд: e-motion Страницы: 2

Бренд: Lastolite Страницы: 3

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

Southern Series

Бренд: Warmington Страницы: 2

Бренд: BrandMotion Страницы: 8

Бренд: SICK Страницы: 119

Бренд: Hama Страницы: 40

Бренд: Actia Страницы: 37

Kitchen meat grinder

Бренд: OBH Nordica Страницы: 24

Бренд: PAC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды