manualshive.com logo in svg

Daktronics BA-1018, Руководство пользователя

Поделиться
Скачать
Daktronics BA-1018 Скачать руководство пользователя страница 66

 

Section 9: 

Team Name Message Center 

Maintenance 

 

IMPORTANT NOTES: 

 

1.  Disconnect power before doing any repair or maintenance work on the 

message centers. 

 

2.  Permit only qualified service personnel to access the internal electronics 

of the display. 
 

3. 

Disconnect power when the scoreboard is not in use.

 

9.1  Team Name Message Center System Overview 

Team name message centers (TNMCs) are available in two sizes: an 8x32 matrix 
model with four 8x8-pixel modules, and an 8x48 model comprised of six 8x8 
modules. 

Figure 13

, below, illustrates the larger unit. Light emitting diodes (LEDs) 

– tiny, solid-state lighting units – illuminate the displays. 
 

 

 

Figure 13: 8x48 Team Name Message Center 

The message centers feature an array of red or amber LEDs, and are capable of 
displaying characters up to 10" high. Pixels in the red TNMC consist of a three-LED 
cluster, while amber TNMCs use four-LEDs per pixel. 
 
The four-module TNMC measures approximately 1'-4" tall by 4' wide, while the six-
module TNMC measures approximately 1'-4" by 6' wide; both have an in-cabinet 
depth of about 5". The smaller units weigh about 80 pounds per pair, and the larger 
TNMC sets add about 120 pounds to scoreboard weight. 
 
TNMCs are typically installed in pairs. Although the message centers customarily 
are used for team names (home and guest), they are programmable and can display 
any type of caption. Characters are shown on a single line and either single- or 
double-stroke fonts may be used for the caption or name.  

TNMC Maintenance 

9-1

 

 

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды