Daktronics BA-1018 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 216

background image

Scoreboard Options

10-3

6.

Screw the trumpet into the horn body. The trumpet will tilt down about 10
degrees to allow moisture drainage

.

7.

Connect to power to the scoreboard.

8.

Connect the control console to the scoreboard.

9.

Test the horn by pressing the key labeled

HORN

on the control console.

DC Trumpet Horn Installation (Externally Mounted)

Caution:

Disconnect scoreboard power before installing the horn!

Refer to

Drawings A-128938

and

A-162102

for complete installation information.

With single-section scoreboards, the external horn mounting location is above the
center-most door. If the horn is ordered with a new scoreboard, the horn power
enclosure assembly (

Steps 3 4, and 5,

below) will be factory-installed, already

attached to the interior back panel of the scoreboard. If the horn is added later,
attachment of the horn power enclosure assembly will be part of the installation. In
either case, the horn interconnect harness is also factory-installed and ready for the
final attachment with the horn.

1.

Locate the horn panel near the top of the scoreboard. Refer to the
component locations drawings listed in

Section 4

. Note that there is a 2"

knockout in this panel.

2.

Loosen the screws securing the bottom of the panel and swing it open.

3. Note:

This step and the next two are not required if the horn is ordered as

original equipment; these procedures will be completed at the factory.

In

the interior back panel of the scoreboard, drill two

5

/

32

" holes 4" apart.

These screw holes will be used to attach the horn power enclosure
assembly, so they should be located within reach of the 2" knockout in the
horn panel. Refer to the

Figure 3

detail on

Drawing A-162102

.

4.

Attach the horn power enclosure assembly to the inside of the scoreboard,
using #10 tapping screws in the

5

/

32

" holes.

5.

Attach the plate assembly to the horn enclosure using the #10 hardware
provided.

6.

Remove the 2" knockout in the horn access panel. Note that there are two

7

/

32

" holes on either side of the knockout.

7.

Thread the two gray wires from the horn through the top of the mounting
angle.

8.

Attach the horn to the mounting angle using the #10 hardware provided

9.

Insert the bushing into the

3

/

8

" hole in the mounting angle.

10.

Place the horn/angle assembly over the 2" knockout and

7

/

32

" holes in the

front panel of the scoreboard. Attach the assembly using the #10 hardware
provided.

11.

Open the front panel and remove the cover from the horn enclosure.

12.

Use the wire nuts provided to attach one gray wire from the horn to the
black wire from the plate assembly. Connect the second gray wire from the
horn to the red wire from the plate assembly.

«
...
78
79
80
81
82
...
»

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BA-1018

Бренд: DAPU Страницы: 4

Бренд: RAKINDA Страницы: 20

Бренд: ZALMAN Страницы: 20

Бренд: Hagan Страницы: 32

Бренд: Warmup Страницы: 4

Бренд: X4-Life Страницы: 2

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: Ledvance Страницы: 6

Бренд: VDO Страницы: 236

Бренд: Kambrook Страницы: 12

Бренд: PullRite Страницы: 10

Бренд: Viking Страницы: 1

Бренд: TecnoVideo Страницы: 4

Бренд: Mystic Romance Страницы: 10

Бренд: ZiFiSense Страницы: 14

Бренд: Whispbar Страницы: 85

Бренд: J-3 International Holding Co. Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды