manualshive.com logo in svg

Daktronics BA-1018, Руководство пользователя

Поделиться
Скачать
Daktronics BA-1018 Скачать руководство пользователя страница 42

 

Mechanical Installation

 

 

 

6-5

 

Use a spreader bar. 

 

Use every lifting point provided. 

 

Take special care not to exceed the rated load of the eyebolts. Refer to 

ED-7244

,

 

Eyebolts

, to determine allowable loads and load angles for the lifting hardware.  

ED-7244

 is located in 

Appendix B 

of this manual. 

 
Avoid using other lifting methods. Cables and chains attached to the eyebolts and 
directly to a center lifting point, as shown in the right-hand example in 

Figure 3

, can  

create a dangerous lateral force on the eyebolts and may cause the eyebolts to fail. 
Daktronics scoreboards use 

1

/

2

" and 

5

/

8

" shoulder-type eyebolts mounted to a 

1

/

8

" 

aluminum plate or steel nut plate, but exceeding load angles or weight limits could 
cause the bolts to pull out of the scoreboard cabinet to buckle. In either 
circumstance, there could be serious damage to the scoreboard. If you must use this 
method, ensure a minimum angle between the chain and scoreboard of at least 45 
degrees. 

 
Note:

 Daktronics assumes no liability for scoreboard damage resulting from 

incorrect setup or incorrect lifting methods

. 

 
Eyebolts are intended for lifting only. Do not attempt to permanently support the 
display by the eyebolts. 
 
In installations in which an ad panel or some other scoreboard section may be added 
to the base display, the lower scoreboard section is installed first and secured to the 
support beams, and then the upper section is placed atop or above the lower section 
and attached to the beams. There may be cables extending from the top of the lower 
section. Guide these cables into the hole in the bottom of the upper section for later 
connection.  
 
If installers remove the lift eyebolts, plug the holes with bolts and the rubber sealing 
washers used with the eyebolts. Apply silicone or another waterproof sealant to the 
eyebolt openings. Inspect the top and sides of the display for any other holes or 
openings that may allow moisture to enter the display and plug and seal those 
openings as well.

Содержание BA-1018

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды