Daikin DC97MC, Руководство по установке

Страница: 29 / 64

29
24 V
OLT
T
HERMOSTAT
W
IRING
W
IRE ROUTING MUST NOT INTERFERE WITH CIRCULATOR BLOWER
OPERATION
,
FILTER REMOVAL OR ROUTINE MAINTENANCE
.
A
REMOVABLE PLUG CONNECTOR IS PROVIDED WITH THE FURNACE
CONTROL TO MAKE THERMOSTAT WIRE CONNECTIONS
. T
HIS PLUG MAY
BE REMOVED
,
WIRE CONNECTIONS MADE TO THE PLUG
,
AND
REPLACED
. I
T IS RECOMMENDED THAT MULTIPLE WIRES
BE JOINED WITH A WIRE NUT AND A SINGLE CONDUCTOR BE INSERTED
UNDER THE TERMINAL SCREW
. F
AILURE TO DO SO MAY RESULT IN
INTERMITTENT OPERATION
.
STRONGLY
- HEAT SET-UP DIP SWITCH DIP
SWITCH
#13 MUST
BE SET TO
MATCH THERMOSTAT TYPE
. T
O USE THE
CTK01
COMMUNICATING
THERMOSTAT
, DIP
SWITCH
#13
MUST BE SET TO
ON
POSITION
. T
HIS IS
ALSO THE CORRECT SETTING FOR A NON
-
COMMUNICATING
2-
STAGE
THERMOSTAT
. T
O USE
CTK02**, CTK03**
OR
CTK04**
MODULATING THERMOSTAT
,
CHECK TO MAKE SURE
DIP
SWITCH
#13
IS
IN THE
OFF
POSITION
(
FACTORY POSITION
). T
HIS IS ALSO THE CORRECT
POSITION WHEN USING A NON
-
COMMUNICATING SINGLE
-
STAGE
THERMOSTAT
.
IMPORTANT NOTE
When installed with a non-communicating thermostat, the
furnace integrated control module provides terminals for both
“W1” and “W2”, and “Y1” and “Y2” thermostat connections.
This allows the furnace to support the following system appli-
cations: ‘Two-Stage Heating Only’, ‘Two-Stage Heating with
Single Stage Cooling’, and ‘Two-Stage Heating with Two-Stage
Cooling’. Refer to the following figures for proper connec-
tions to the integrated control module.
Low voltage connections can be made through either the right
or left side panel. Thermostat wiring entrance holes are lo-
cated in the blower compartment. The following figure shows
connections for a “heat/cool system”.
This furnace is equipped with a 40 VA transformer to facilitate
use with most cooling equipment. Consult the wiring dia-
gram, located on the blower compartment door, for further de-
tails of 115 Volt and 24 Volt wiring.
NOTE: Use of cooling ramping profiles and dehum feature
requires a jumper between Y1 and O when a straight cooling
unit is used.
T
HERMOSTAT
“R”
REQUIRED IF OUTDOOR UNIT IS EQUIPPED WITH A
C
OMFORT
A
LERT
™
MODULE OR IF THE OUTDOOR UNIT IS A PART OF
THE
C
OMFORT
N
ET
™
FAMILY OF EQUIPMENT
.
IMPORTANT NOTE
AUX
DE
HUM
W2
C 1
Y1
2 R
W1
Y2
G O
24 V THERMOSTAT CONNECTIONS
Low Voltage Connections with Auxiliary Terminals
Figure 31
The auxiliary contacts are shipped with a factory installed
jumper. As an option, the auxiliary contacts may be wired
to a normally closed float switch. In the event of open
contacts, the gas heat and cooling will be disabled until
the condition is corrected. These are 24 volt terminals
powered internally, do not apply another voltage source
to these terminals.
THERMOSTAT
R
Y C
NEU
Furnace Integrated
Control Module
Remote
Condensing Unit
(Single-Stage Cooling)
Dehumidistat
[Optional]
R
Thermostat - Single-Stage Heatingwith Single-Stage Cooling
Figure 32
T
O USE A SINGLE
-
STAGE
H
EAT
T
HERMOSTAT
, DIP
SWITCH
#13
ON THE
FURNACE CONTROL BOARD MUST BE SET TO THE
OFF
POSITION
.
IMPORTANT NOTE
THERMOSTAT
R
Y C
Furnace Integrated
Control Module
Remote
Condensing Unit
(Single-Stage Cooling)
Dehumidistat
[Optional]
NEU
R
Thermostat - Two-Stage Heating with Single-Stage Cooling
Figure 33