Daikin AVV Скачать руководство пользователя страница 58

Страница: 58 / 76

IM 817-7

58 www.DaikinApplied.com

Controls by Others - Variable

Airflow

An optional EC motor with “variable fan speed control”

allows a field provided DDC controller to modulate the

unit airflow between 50% and 100% of nominal unit

airflow in a single zone variable air volume sequence.

In continuous fan mode the benefits of Single Zone VAV

include sound reduction, energy savings, and consistent

and precise temperature control for improved comfort

with better air mixing and less stratification. In humid

climates, the ability to deliver a wide range of fan speeds

is particularly effective for de-humidification.

Note:

This option is not available with MicroTech controls.

Making Control Connections

For field provided control wiring connections refer to the

appropriate control wiring schematic,

page 59

page

Connect the field supplied controller to the harness

provided. A 0-10VDC fan control signal must be provided

between ground and wire 33. For RPM/data out signal,

connect controller to wire 34.
The variable fan speed scale is linear between a

minimum 50% airflow at 2vdc and a maximum 100%

airflow at 10vdc as shown in

Figure 120

. Reducing the

input signal to 0vdc will cause the motor to turn off. Care

should be taken when using variable airflow on units with

DX cooling as lower airflow may increase the risk of coil

freeze-up. Variable airflow control should not be used on

units with electric heat.

Figure 118: 0-10VDC Variable Fan Speed Control

100

0-10 VDC Control Signal

% Nominal Unit Airflow

Содержание AVV













































































Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды

Daikin AVV, Руководство по установке и обслуживанию

Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды