Daikin AVV Скачать руководство пользователя страница 34

Страница: 34 / 76

IM 817-7

34 www.DaikinApplied.com

Heating – Modulating Valve Piping

Hot Water (or 2-pipe CW/HW) Modulating

Valve Piping

When piping the modulating valve, refer to the arrows on

the modulating valve body to determine the direction of

flow. The valve should be installed so that there is a 2"

(51mm) minimum clearance to remove the actuator form

the valve body. Provide unions for removal of unit coil

and/or control valve as a future service consideration.

Hot water connections may be same end as cooling coil

connections, but are recommended to be opposite end

to facilitate piping. When using Daikin Applied MicroTech

controls, they must be opposite end. The modulating

valve accessory must be field installed on the unit for

which it was selected.

CAUTION

Refer to the arrow on the modulating valve body to determine the

direction of flow. If the valve is mounted improperly, the unit will

not operate properly and damage to the valve may result.

2-Way Modulating, Normally Open, Hot

Water or 2-pipe CW/HW Valve Piping

(typical)

The 2-way Modulating hot water (or 2-pipe CW/HW)

valve is furnished normally open to the coil. When the

valve is de-energized (off) there is full flow through the

coil. Energizing the valve reduces the volume of water

flow in a modulating fashion.

Figure 88:

2-Way Modulating Valve Control, Normally

Open, Hot Water or 2-pipe CW/HW Piping

Unit Coil

2-Way

Modulating

Valve

Return

Supply

Unions

Balancing and Shutoff Valve

Shutoff Valve

Supply

Return

OCT Sensor

(2-pipe CW/HW

Units Only)

3-Way Modulating, Normally Open, Hot

Water or 2-pipe CW/HW Valve Piping

(typical)

The 3-way Modulating hot water (or 2-pipe CW/HW)

valve is furnished normally open to the coil. When the

valve is de-energized (off) there is full flow through the

coil. Energizing the valve allows a varying amount of

water to bypass the coil.

Figure 89: 3-Way Modulating Valve Control

Unit Coil

3-Way

Modulating

Valve

Return

Supply

Union

Balancing and Shutoff Valve

Shutoff Valve

Supply

Return

Union

Balancing Valve

OCT Sensor

(2-pipe CW/HW

Units Only)

Note:

The

port is always piped to the coil. Actuator to be

configured for

port to be Normally Open.

Содержание AVV













































































Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды

Daikin AVV, Руководство по установке и обслуживанию

Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды