Daikin AVV Скачать руководство пользователя страница 54

Страница: 54 / 76

IM 817-7

54 www.DaikinApplied.com

Digital Ready Unit Mounted

Temperature Sensor Specifications

A 10 K ohm Negative Temperature Coefficient (NTC)

sensor and a 1 K ohm Positive Temperature Coefficient

sensor is provided for the discharge air, outdoor air and

room air temperature measurement. They are located

next to each other in the air stream as shown in

Figure

113

. Each is wired to the terminal strip separately so that

the Automatic Temperature Control contractor may select

the appropriate sensor for the application.

10 K ohm NTC Sensor

The 10 K ohm NTC sensor is constructed from stainless
steel with an epoxy seal and twisted wire leads.

Type:

10K ohm @ 25°C

Accuracy:

±0.2°F, 40°F - 80°F

±0.36°F, 32°F - 158°F

1 K ohm PTC Sensor

The 1 K ohm sensor is a shrink-wrap encapsulated, PTC

silicon sensing element with stranded, tinned copper

wire leads (#22 AWG).

Type:

1035 ohm @ 25°C

Accuracy:

±0.9°F, 5°F - 167°F

Figure 113: Sensor Locations

Discharge Air Sensor

Room Air Sensor

Holes in Front

Access Panel

Outdoor Air Sensors

Outdoor Air

Opening

Table 38: Temperature Sensors Resistance Values

10 K ohm (NTC)

Temperature (

-40

-20

Resistance (ohms)

337200

97130

32660

12490

10000

8056

5326

3602

2489

1 K ohm (PTC)

Temperature (

-40

-20

Resistance (ohms)

613

727

855

997

1035

1074

1153

1237

1323

Содержание AVV













































































Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды

Daikin AVV, Руководство по установке и обслуживанию

Результаты поиска

Содержание AVV

Отзывы:

Похожие инструкции для AVV

Бренды по названию

Популярные бренды