Daedong Kioti RX6020 Скачать руководство пользователя страница 173

Страница: 173 / 262

3-poInt HItcH ImpLement And LoAdeR opeRAtIon

H11O566A

5. Install the lower link to the imple-

ment and fit the pins.

(1) Lower Link

6. start the engine and drive back-

ward toward the implement. then,

the lower link end is inserted to its

original position.

(1) Lower Link end

H11O569A

7. separate the top link from its

bracket and turn it to adjust its

length so that it becomes close to

the upper bracket mounting hole

of the implement. Then, fit it to the

mounting hole, insert the lock pins,

and secure it with the snap pin.

Remove the implement support as

necessary.

(1) top Link (3) snap pin

(2) Lock pin

H11O561A

TF110(RX7320)ROPS합본-US,EU,AU-06.3 3

2016-06-07 오후 7:21:18

Содержание Kioti RX6020







































































































































































































































































Результаты поиска

Содержание Kioti RX6020

Отзывы:

Daedong Kioti RX6020, Руководство пользователя, Страница: 173 / 262

Результаты поиска

Содержание Kioti RX6020

Отзывы: