Daedong Kioti RX6020 Скачать руководство пользователя страница 152

Страница: 152 / 262

RX6020 / RX6620 / RX7320 / RX7620

M55O550A

4. make sure both brake pedals are

interlocked.

(1) Brake pedal (lH / RH)

(2) pedal Interlock

(A) depress

If depressing only one brake

pedal at a high speed, the trac-

tor can lose its balance and be

overturned.

•

WARNING

5. When an implement is attached to

the tractor, pull the position control

T11O452A

(1) position Control lever

(2) lock Bolt

(3) lower link (A) lifting (B) lowering

M55O547A

lever to the rear side of the tractor

to lift the implement.

6. Increase slowly the engine Rpm

from idle speed to medium speed.

(1) Hand Throttle lever

" "Slow"

"Fast"

TF110(RX7320)ROPS합본-US,EU,AU-05.12 12

2016-06-07 오후 7:20:28

Содержание Kioti RX6020







































































































































































































































































Результаты поиска

Содержание Kioti RX6020

Отзывы:

Daedong Kioti RX6020, Руководство пользователя, Страница: 152 / 262

Результаты поиска

Содержание Kioti RX6020

Отзывы: