Daedong Kioti RX6020 Скачать руководство пользователя страница 113

Страница: 113 / 262

description oF operating system

T11O452A

POSITION CONTROl lEvER

(1) position control lever

(2) lock bolt

(3) lower link

(a) lifting

(b) lowering

the position control lever is used to

adjust the height of implements on

the 3-point hitch ends.
the implement attached to the lifting

arm can be lowered by pushing the

lever while the implement is raised

by pulling the lever.
in order to limit the lowering height of

implements, use the lock bolt (2) to

limit the operating range of the lever.
For detailed information, refer to

"3 point hitch control" in chapter 5.



Make sure that the seat belt

is not twisted. It cannot work

properly, leading to a hazard-

ous condition.



The seat belt should go around

your body as low as possible,

not your waist or abdomen.

Otherwise, the seat belt cannot

protect you properly.

WARNING

TF110(RX7320)ROPS합본-US,EU,AU-04.41 41

2016-06-07 오후 7:17:43

Содержание Kioti RX6020







































































































































































































































































Результаты поиска

Содержание Kioti RX6020

Отзывы:

Daedong Kioti RX6020, Руководство пользователя, Страница: 113 / 262

Результаты поиска

Содержание Kioti RX6020

Отзывы: