D-Link DSL-2544N Скачать руководство пользователя

Страница: 66 / 68

Appendix A – Networking Basic

D-Link DSL-2544N User Manual

Networking Basics

Check Your IP Address

After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless

router) automatically. To verify your IP address, please follow the steps below.

Click on

Start

Run

. In the run box type

cmd

and click on the

button.

At the prompt, type

ipconfig

and press

Enter

This will display the IP address, subnet mask and the default

gateway of your adapter.

If the address is 0.0.0.0, check your adapter installation,

security settings and the settings on your router. Some

firewall software programs may block a DHCP request on

newly installed adapters.

If you are connecting to a wireless network at a hotspot (e.g.

hotel, coffee shop, airport), please contact an employee or

administrator to verify their wireless network settings.

Содержание DSL-2544N





































































Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды

D-Link DSL-2544N, Руководство пользователя

Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды