D-Link DSL-2544N Скачать руководство пользователя

Страница: 19 / 68

Section 3 – Web Configuration

D-Link DSL-2544N User Manual

Static IP

If the internet service you subscribed is Static IP, the Protocol is set to

be Static IP, the page shown as the figure appears on the right.

In this page, enter the

IP Address

Subnet Mask

Default Gateway

and

Primary DNS Server

provided by your ISP.

If the Protocol is set to be

Dynamic IP

and

Bridge

, the content of the page will

be slightly different.

After settings, click

Next

to go to the next page.

Step 6

Configure the wireless network. Enter the information and click

Next

The following table describes the fields in this page.

Field

Description

Enable Your

Wireless

Network



To enable or disable wireless network

connection.

Wireless

Network Name

(SSID)



Set a name for your wireless network.

Visibility status



Visible: Your SSID can be found by wireless

clients.



Invisible: Your SSID is hided. Wireless clients

need to manually enter your SSID and connect.

Security Mode

You can choose a security mode to protect your

wireless network. It is recommended selecting

WPA2-PSK

WPA2

Pre-Shared Key

Enter a password. The length of the password is

between 8-63 characters.

Содержание DSL-2544N





































































Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды

D-Link DSL-2544N, Руководство пользователя

Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды