D-Link DSL-2544N Скачать руководство пользователя

Страница: 57 / 68

Section 3 – Web Configuration

D-Link DSL-2544N User Manual

Maintenance

System

Choose

MAINTENANCE

System

. The

System

page is shown as the figure

appears on the right.

In this page, you can reboot device, back up the current settings to a file, update

and restore the settings from the file saved previously, and restore the factory

default settings.

The buttons in this page are described as follows:



Reboot

: Reboot the device.



Backup Settings

: Save the settings to the local hard drive. Select a location

on your computer to back up the file. You can name the configuration file.



Update settings

: Click

Browse

to select the configuration file of device and

click

Update Settings

to restore the device configuration.



Restore Default Settings

: Reset the device to default settings.

Notice

: Do not turn off your device or press the

Reset

button while an operation in

this page is in progress.

Содержание DSL-2544N





































































Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды

D-Link DSL-2544N, Руководство пользователя

Результаты поиска

Содержание DSL-2544N

Отзывы:

Похожие инструкции для DSL-2544N

Бренды по названию

Популярные бренды