D-Link dgs-8000 SERIES Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 97

D-Link dgs-8000 SERIES Скачать руководство пользователя страница 32

DGS-8000 Series Hardware Installation Guide Chapter 1 Product Overview

25

1.4.5.3

Technical Specifications

Table 12 8000-48PC-E technical specifications

Product
Model

8000-48PC-E

Ports

44 RJ-45 ports for 10/100/1000BASE-T, four fiber/copper combo ports. A maximum
of 48 PoE ports are supported.

Fiber
Transceiver
supported

Supported SFP Transceivers:
1. DEM-210 (100Base-FX, Multi-mode, 2km)
2. DEM-211 (100Base-FX, Single-mode, 15km)
3. DEM-310GT (1000Base-LX, Single-mode, 10km)
4. DEM-311GT (1000ase-SX, Mutli-mode, 500m)
5. DEM-312GT2 (1000Base-SX, Multi-mode, 2km)
6. DEM-314GT (1000BASE-LX, Single-mode, 50km)
7. DEM-315GT (1000BASE-LX, Single-mode, 80km)
8. DGS-712 (1000Base-T)

Supported SFP WDM transceivers:
1. DEM-220T (100Base-FX, Single-mode, 20km, TX-1550/RX-1310nm)
2. DEM-220R (100Base-FX, Single-mode, 20km, TX-1310/RX-1550nm)
3. DEM-330T (1000Base-LX, Single-mode, 10km, TX-1550/RX-1310nm)
4. DEM-330R (1000Base-LX, Single-mode, 10km, TX-1310/RX-1550nm)
5. DEM-331T (1000Base-LX, Single-mode, 40km, TX-1550/RX-1310nm)
6. DEM-331R (1000Base-LX, Single-mode, 40km, TX-1310/RX-1550nm)

LED Status,

Link/ACT

Hot swap

Supported

Power
consumption

< 121 W + 15.4 x N (N indicates the number of PoE ports used, N

≤

48)

EMC

GB9254-1998 Class A; FCC Class A

Safety GB4943-2001

Operating
temperature

0 to 50°C

Storage
temperature

-40 to 70°C

Operating
humidity

10% to 90% RH

Weight 3.8kg

(net)

Dimensions
(L x W x H)

436 x 346 x 45 mm

«
...
30
31
32
33
34
...
»

Содержание dgs-8000 SERIES


































































































Отзывы:

Нет отзывов