CYBEX Arc Trainer 630A Скачать руководство пользователя страница 53

Страница: 53 / 70

Arc Trainer

Hardware Pack

Tools Required

• Phillips head screwdriver
• 7/32” Hex key (supplied with kit)
• 3/16” Hex key (supplied with kit)

1. Read and understand all instructions
thoroughly before installing this kit.

2. Verify kit contents. See Figure 1.

Kit No. 610AK017

Instruction Sheet

Figure 2

Figure 1

3. Install the hardware pack.

Install the hardware as shown in Figure 2.

Refer to Chapter 5 of the Arc Trainer 610A
Owner’s Manual part number 5610A-4 for
detailed instructions.

NOTE:

Place a drop

of loctite (10) on the SHCSC (7) and place
another drop of loctite into the shaft where
the SHCSC (10) will be tightened into).

Allen wrench, 3/16”,
BK030201, (1)

Allen wrench, 7/32”,
BK030204, (2)

Linkage Rod Cap,
PL-16535, (2)

Washer .281 x .50,
HS307601, (2)

SHCSC .250-20 x .75
HX622815, (2)

Flange Spacer,
600A-311, (2)

BHSCS .375-16 x 1.50,
JC700422, (4)

Internal Tooth Lockwasher,
JS347400, (4)

Pan HD Phil HD Self Tapping
8-16 x .75 Type WB Black
HT552515, (2)

Water
Bottle

Holder

Loctite #242,
YA000201, (1)

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.

Arc Trainer® and its mark are registered trademarks of Cybex International, Inc.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 • www.cybexinternational.com • [email protected]

Содержание Arc Trainer 630A







































































Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Похожие инструкции для Arc Trainer 630A

Бренды по названию

Популярные бренды

CYBEX Arc Trainer 630A, Руководство по обслуживанию

Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Похожие инструкции для Arc Trainer 630A

Бренды по названию

Популярные бренды