CYBEX Arc Trainer 630A Скачать руководство пользователя страница 64

Страница: 64 / 70

Figure 21

To Fitness

Equipment

RJ-45

Power Inlet

12 VDC

Antenna/

Cable

Source

(Coax Cable)

To CSAFE

Device

Secure the power cable to the monitor plate

using the cable tie (P). See Figure 22.

Figure 22

Power

Cable

Secure Cable

Tie Here

Monitor

Plate

Figure 23

(Q)

Back

Cover

Install back cover to the monitor (Q). See

Figure

23.

16. Plug in AC/DC Adapter, coax and power
cables.

Locate the AC/DC adapter (W) supplied with

the monitor and plug into the power cable

exiting the base of the Arc.

Plug the power cord (X) into the AC/DC

adapter

(W).

NOTE:

Power cord (X) varies by

country.

Thread the antenna/cable source cable

(supplied at the site location) into the

coax cable exiting the base of the Arc.

17. Set up monitor for first time use.

Locate the Personal Entertainment Monitor

Manual (LT-20191) and follow the set up

procedure in Chapter 5.

Plug the power cord (X) into a wall outlet.

Plug headphones (not supplied) into

headphone jack located at base of console.

Refer to Chapter 3 of the Personal

Entertainment Monitor Manual (LT-20191)

regarding use of the channel and volume

keys located on the lower center of the

Arc console. See Figure 24.

Figure 24

Channel

Keys

Volume

Keys

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.

Arc Trainer® and its mark are registered trademarks of Cybex International, Inc.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 • www.cybexinternational.com • [email protected]

Содержание Arc Trainer 630A







































































Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Бренды по названию

Популярные бренды

CYBEX Arc Trainer 630A, Руководство по обслуживанию

Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Бренды по названию

Популярные бренды