CYBEX Arc Trainer 630A Скачать руководство пользователя страница 66

Страница: 66 / 70

7. Remove the blank plate.

Using a Phillips head screwdriver, remove the two

screws securing the blank plate in place. See
Figure 4.

Remove blank plate.

Screw (2)

Blank Plate

Figure 4

Controller Cover

Power
Supply
Cable

Controller Board

Screw (2)

9. Connect power supply cable to controller board.

Using a Phillips Screwdriver, remove the two screws

securing the controller cover. See Figure 5.

Remove cover.

Push power supply cable through hole in controller

cover.

Firmly press power supply cable jack into the

connector on the controller board.

8. Install power supply.

Install power supply in place of blank plate that

was removed in step 7B.

Using a Phillips head screwdriver, install the two

screws (removed in step 7A) securing the power
supply. See Figure 4.

Route power supply cable (follow existing cables)

up through frame to control board.

Figure 5

Using a Phillips screwdriver, install and tighten the

two screws removed in step 9A.

Secure power supply cable to the other cables

using the cable tie.

10. Reinstall left shroud.

Place left shroud in place.

Using a Phillips screwdriver, install the ten screws

and two washers securing the shroud removed in
step 6A.

Securely tighten all screws.

11. Reinstall access cover.

While being sure not pinch any cables, hold the

access cover in place. See Figure 2.

Using a Phillips screwdriver, install and tighten

the two upper screws ﬁ rst (removed in step 5B).

NOTE:

Do not over tighten screws.

Install and tighten the two lower screws (removed

in step 5A).

NOTE:

Do not over tighten screws.

12. Install warning decals.

Peel off backing and install the two warning decals

as shown in Figures 6 & 7.

NOTE:

The “Disconnect

Power” decal must be installed in location shown in
Figure 6. The “Medical Inlet” decal must be installed
in location shown in Figure 7.

For connec

tion to a Me

dical Grade

outlet only

to ensure pr

oper groun

ding.

Voltage: 10

0-240 VAC~

50/60Hz

DE-19547-4

WARNING

13. Test unit for proper operation.

CM000240 E

ɈɌɄɅɘɑɂɌȿ
ɉɂɌȺɇɂȿ

ɉɊȿɀȾȿ ɑȿɆ
ɉɊɂɋɌɍɉȺɌɖ
Ʉ ɈȻɋɅɍɀɂȼȺɇɂɘ

ɉɊȿȾɍɉɊȿɀȾȿɇɂȿ

For connection to a Medical Grade
outlet only to ensure proper grounding.

Voltage: 100-240 VAC~
50/60Hz

0.75

Amps

1-Phase

DE-19547-4

WARNING

Figure 7

Figure 6

Reinstall controller cover.

Cybex

and the Cybex logo are registered trademarks of Cybex International, Inc.

Arc Trainer

and its mark are registered trademarks of Cybex International, Inc.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 • www.cybexinternational.com • [email protected]

Содержание Arc Trainer 630A







































































Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Похожие инструкции для Arc Trainer 630A

Бренды по названию

Популярные бренды

CYBEX Arc Trainer 630A, Руководство по обслуживанию

Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Похожие инструкции для Arc Trainer 630A

Бренды по названию

Популярные бренды