CYBEX Arc Trainer 630A Скачать руководство пользователя страница 21

Страница: 21 / 70

Arc Trainer

Pivot Cover

Kit No. 610AK004 (Left Hand Pivot Cover)

610AK005 (Right Hand Pivot Cover)

Installation Instructions

NOTE:

This instruction sheet describes how to

replace the pivot cover in the Arc Trainer 610A.

Tools Required

• 7/32” Allen wrench (2)

1. Read and understand all instructions thoroughly
before

installing this kit.

2. Verify you received the following (see Figure 1):

Pivot Cover (see appropriate kit number listed

above).

Loctite #242, YA000201 (not shown)

Remove existing pivot cover.

Insert the new pivot cover in place (“Cybex”

faces

out).

Locate two of the BHSCS/pivot shaft retainers

removed from step 3B.

Place a drop of loctite (B) on both of the

BHSCS. Place another drop of loctite in the

shaft (where each SHCS will be tightened into).

Tighten both screws securely.

Repeat steps 3E through 3G to install the other

screws/washers.

Turn the main power switch to the on (I)

position.

Test the unit to verify proper operation.

Figure 1

Figure 2

3. Replace the pivot cover.

Turn the main power switch above the power

inlet to the off (0) position.

Using two 7/32” Allen wrenches, remove the

four BHSCS and pivot shaft retainers securing

the pivot cover.

NOTE:

Once one of the two

screws is removed (two in front and two in

back), carefully wedge an Allen wrench into the

shaft in order to remove the other screw from

the

shaft.

See Figure 2.

BHSCS/Loctite

Pivot
Shaft
Retainer

BHSCS/
Loctite

Do not remove shaft...shown
exploded for visual detail.

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.

Arc Trainer® and its mark are registered trademarks of Cybex International, Inc.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 • www.cybexinternational.com • [email protected]

Содержание Arc Trainer 630A







































































Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Бренды по названию

Популярные бренды

CYBEX Arc Trainer 630A, Руководство по обслуживанию

Результаты поиска

Содержание Arc Trainer 630A

Отзывы:

Бренды по названию

Популярные бренды