CXR CIP-2ALL, Руководство пользователя

Страница: 10 / 54

User manual CIP-ALL
CIP-ALL - Page 10
important Information
Conformity Statement EC
Manufacturer name: CXR
Manufacturer address: rue de l'Ornette - 28410 ABONDANT – France
Product name: CIP-ALL
The CE mark attests the conformity of this equipment to the main requirements of the R&TTE 1999/05/CEE European community (until June
12
th
2016), and LVD 2014/35/UE – CEM 2014/30/UE (from June 13
th
2016):
- For the user’s safety: in compliance with the Directive 2006/95/EC (until April 19
th
2016) and Directive 2014/35/UE (from April 20
th
2016) as per EN.60950 standard
- For electromagnetic compatibility: in compliance with the Directive 2004/108/EC (until April 19
th
2016) and Directive 2014/30/UE (from
April 20
th
2016) as per EN.55022 and EN.55024 standards.
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense. Modifications not expressly approved by the
manufacturer could void the user's authority to operated the equipment under FCC rules.
Safety Instructions
The following accesses are referenced as SELV (Safety Low Voltage] in conformity with EN.60950 standards:
•
12/24/48 Vdc Input
•
Admin : RS-232 console port
•
Term : RS-232 terminal interface
•
LAN : Ethernet port 10 Base T / 100 Base TX MDI/MDI-X
•
FO : Optical Gigabit Ethernet port
•
Analog Port: Analog ALL, FXS, FXO, EM
•
E1 port on option
The power cord is the main switching element. Thus the mains outlet must be installed close to the equipment and provide easy access. In
order to comply with the safety regulations, it is imperative to use only the accessories (cables) provided with the equipment. When access to
the inside of the modem is necessary it is imperative to disconnect the power source.
For safety reasons, any operation on the equipment and particularly opening the enclosure must be carried out by maintenance person qualified
by CXR.
The equipment must imperatively be returned to CXR in any case of anomaly, fall, loss of performance, water exposure, power supply damage,
power or line cord damage, or anything else that can provide a safety concern…
Environmental
The CIP-ALL is designed for residential or light industrial use within the following environmental conditions:
•
Storage Temperature : -10 to +70 °C
•
Operating Temperature : -10 to +60 °C
•
Hygrometry : 0 to 90% without condensation
•
Class : IP40
•
Flammability : UL94-V0
Place the equipment in an area well suited for its good operation and its longevity:
•
Equipment must not be exposed to excessive solar radiation
•
Equipment must not be in contact with water. It must not be used near a water reserve or in a wet location.
•
Equipment must be installed on a plane and horizontal surface, without vibration.
•
Make sure the area is clean, dry and exempt of dust
•
Make sure that nothing could obstruct the air vent of the product, and that no small size part (screw, staple, clip, …) could get into it.
•
Always disconnect the line and mains connections before any operation (move, connecting other equipment, …) on the equipment. The
mains cord must be taken from the socket; any effort on the cord could induce damages and risk of electrical shock.
Use
The CIP-ALL is intended to transport analog voice signals, 2/4 wires Leased Line interface, or FXO interface for a PBX connection, or FXS
interface for a telephone set connection, or 8 wires for E&M line interface.
The WAN port is either a 10/100BT or an optical Gigabit Ethernet port. The analog signal and E1 interface are transported over an Ethernet
packet network.
A POE source option can feed two Ethernet devices connected the Ethernet ports 3 and 4.
The CIP-ALL is compatible with another CIP-ALL, or other equipment complying with CESoPSN (RFC5086) (ask CXR for details).